PS 6-BOLT FRONT Montageanleitung

CENTER LOCK TO 6-BOLT FRONT BOOSTER KIT INSTRUCTIONS
THANKS FOR BUYING A PROBLEM SOLVERS CENTER
LOCK BOOSTER KIT!
We're always looking to provide the products that allow you to configure your
bike any way you want. So if you wanted to mate your non-Boost
wheels to your Boost fork, you've chosen the right product.
WARNING: Cycling can be dangerous. Bicycle products should be
installed and serviced by a professional mechanic. Never modify your bicycle
or accessories. Read and follow all product instructions and warnings including
information on the manufacturer's website. Inspect your bicycle before every
ride. Always wear a helmet.
WARNING: Brakes are essential safety equipment to control and stop your
bicycle. It is therefore strongly recommended that you have this brake product
installed by an experienced professional bicycle mechanic. Failure to install
a brake system component properly may result in accident and serious injury.
For complete ASTM guidelines, and additional product safety information,
please visit problemsolversbike.com/safety
COMPATIBILITY & INTENDED USE
Problem Solvers Center Lock Front Booster Kit is designed to be used with any
Center Lock-compatible 15 x 100mm thru-axle front hub and any Boost-
compatible fork spaced at 15 x 110mm with a 6-bolt rotor.
1-piece and 2-piece rotors are compatible with this kit. NOTE: 2-piece rotors
will not use the serrated 6-bolt washer (Part C).
Intended for ASTM 3 conditions. This is a set of conditions for
the operation of a bicycle on a regular paved surface, unpaved
and gravel roads and trails with moderate grades with
irregular terrain where loss of tire contact with the ground
may occur. As well as rough trails and unimproved trails that
require technical skills. Jumps and drops are intended to be
less than 61cm (24").
INCLUDED PARTS
A. 5mm front hub/axle spacers (2)
B. Center Lock-compatible lock ring
C. Serrated 6-bolt washer
D. Center Lock to 6-bolt adapter
��
��
6400 West 105th Street / Bloomington, MN 55438 / www.problemsolversbike.com
-compatible
™
��
��
TOOLS
External spline lock ring tool
Torque wrench compatible with lock ring tool that measures in Newton meters
Grease
Isopropyl alcohol (rotor cleaner)
INSTALLATION
1. Install the Center Lock to 6-bolt adapter onto the Center Lock hub, with the
six rotor tabs pointed outward.
2. Place your 6-bolt rotor on top of the adapter, aligning the bolt holes with the
rotor tabs.
3. With the serrated surface facing out, place the serrated 6-bolt washer
onto the rotor, once again aligning the bolt holes with the rotor tabs.
NOTE: If using a 2-piece rotor, set aside the serrated 6-bolt washer and
skip step 3. Continue with step 4.
WARNING: Do not use serrated 6-bolt washer with 2-piece rotors.
Doing so may damage the rotor, resulting in an accident and serious injury.
4. Thread on the Center Lock lock ring.
5. Using the torque wrench and external spline lock ring tool, tighten the lock
ring to 40 Nm.
6. Place a 5mm front hub spacer on the non-drive side of the front hub and
install the wheel in the fork end. (Tip: Dab a small amount of grease on the
5mm spacer and the hub end cap, then stick the spacer to the hub before
inserting the front wheel.)
7. Slide the remaining 5mm axle spacer on the drive side of the front hub
between the gap in the fork and the hub.
8. Install the front thru-axle according to manufacturer's specifications.
9. Remove any excess grease from the rotor using isopropyl alcohol.
WARNING: Improper installation of the lock ring may lead to product
failure, causing serious injury. Do not exceed specified torque values.
WARNING: A wheel attachment device that is not properly secured can
allow the wheel to loosen or come off, suddenly stop the wheel, decrease your
control, and cause you to fall.
ONGOING MAINTENANCE
Regularly inspect the Center Lock rotor lock ring and thru-axle for tightness.
Inspect your Front Booster Kit for signs of excessive wear, cracks, or other
fatigue before every ride. If you suspect your Booster Kit
has been damaged, return it to the shop where it was
purchased to be inspected by a professional bicycle
mechanic.
WARRANTY PROCESS
If you and your shop think your Problem Solvers product
is worthy of a warranty inspection, please return the
product to the original place of purchase, accompanied
by a sales receipt.
For complete warranty information, visit
problemsolversbike.com/safety
��
441977 6/20 | 85-000581_INST_B