Gerlach Germany GL 2932 Bedienungsanweisung Seite 5

16. Do not allow the device or power adaptor to wet.
17. If the device falls into water, immediately remove the power plug or power adaptor from
the socket. If the device is powered, do not put hands in the water. Have the device
checked by the qualified electrician before using it again.
18. Do not touch the device or power adaptor with wet hands.
19. Never use this device close to water, e.g.: under shower, in bathtube, or above
sink filled with water.
20. If the device utilises a power adaptor, do not cover it, because this can cause a
dangerous temperature rise and can damage the device. Always connect the power
adaptor cable to the device, and then connect the power adaptor to the power socket.
21. The shaver charging temperature should not be above 35 degrees Celsius or below 5
degrees Celsius.
22. Only the shaver head can be washed in water, the other parts of the shaver cannot be
immersed in water. Be careful, the hot water can cause burns to your hands.
23. Do not use towel or paper tissues for cleaning of shaver head, as they can damage the
head.
Device Description: Timmer Set
1. Trimmer Head 2.Power Button 3. Display 4. Design Trimmer 5. Precision trimmer 6.Nose / Ear trimmer 7. Foil Shaver
8. Sideburn / Eyebrow / Body trimmer 9. Length attachments for the precision trimmer. 10. The docking station 11. Machine Oil.
12. Cleaning Brush 13. Charging cable.
Trimmer Charging:
Before charging make sure, that the shaver is switched off. Charging takes about 1,5 hours. The shaver cannot be plugged into the
power socket for longer than 24 hours.
1. Connect the charger cable to the shaver (fig. 16).
2. The Display(3) will illuminate. And the % of load will show. When it reaches 100% please disconnect the charger.
3. After full charging of the shaver, unplug the charger from the power socket, then disconnect the cable from the shaver.
4. DO NOT use your shaver while charging
Using the device:
1. Make sure the device is not turned on and then insert the needed attachment onto the device.
2. Press the Power button (2). Press it a second time to the second speed.
3. After usage clean the attachment with the brush (12).
5. After several uses please oil the attachment with machine oil (11).
Attachment Usage:
1. Basic trimmer head (1)
This attachment is used to prune and keep the beard looking stylish. Intended for daily use.
To remove and attach please consult Fig. 1, 2, 3. When attaching please align the inside part shown in fig. 3 subpoint 2 with the device's
groove in the device shown in fig. 3 subpoint 1. And then press firmly towards the device until it clicks into place.
To add the length attachment please consult Fig. 11, 12. And then press firmly towards the device until it clicks into place.
To remove the length attachment please consult Fig. 7, 8.
4. Precision trimmer head (4)
This attachment is used for places that the basic trimmer is too big or too wide to reach without cutting parts of your facial hair you don't
intend to cut.
5. Design trimmer head (4)
This attachment is used to adjust the length of your facial hair. You can change one of the 5 length attachments in set (9)
To remove and attach please consult Fig. 1, 2, 3. When attaching please align the inside part shown in fig. 3 subpoint 2 with the device's
groove in the device shown in fig. 3 subpoint 1. And then press firmly towards the device until it clicks into place.
To add the length attachment please consult Fig. 11, 12. And then press firmly towards the device until it clicks into place.
To remove the length attachment please consult Fig. 7, 8. This attachment has 1 attachment that has the option of regulation in 4
positions.
5