Power Cord ..........1 unit Ref. PHS-SA Ref. 0009417 (100V/120V) 0009401 (230V) Kapton Tape ....1 unit Thermocouple .... 1 unit Manual ......1 unit Ref. PH217 Ref. PH218 Ref. 0017155 w w w.jbctools.com Ref. CLMB-A IR Preheater Set Ref. PHS-KB...
Seite 4
Features Heater Unit Heating Area Zone B Fixing brackets Zone A for PHS-SA IR Preheater Support Mains Mains input switch Console socket Pedal socket connection (optional) connection Console Control Unit USB-B connector to PC: - Update the Control Unit software Thermocouple (Type K) Auxiliary Thermocouple (Type K)
Seite 5
w w w.jbctools.com IR Preheater Support Slot Clamps For fixing irregular shaped PCBs to the support. For fixing identical PCBs in the same position. Height Adjustment The PHS-SA allows adjustment for 3 heights between the board and the Heating Area. 28mm ·...
JBCset profiles There are 3 profiles predefined by JBC: A, B and C. The difference between them is the number of steps: 2, 3 or 4. The thicker your PCB is and the more layers it contains, the more steps are needed to obtain a gradual warming.
Seite 7
w w w.jbctools.com Recommended Guidelines 1. Place the Thermocouple (TC) as near as possible to the component being worked on. Fix the TC with Kapton Tape Auxiliary Thermocouple (TC) 2. If there are any sensitive components, use the Auxiliary Thermocouple as protection. You can select the protection temperature in Station settings.
Seite 10
Safety It is imperative to follow safety guidelines to protect health and prevent electric shock, injury, fire or explosions. - Do not use the units for any purpose other than PCB preheating. Incorrect use may cause fire. - The power cord must be plugged into approved bases. Be sure that it is properly grounded before use.
Seite 11
w w w.jbctools.com Specifications IR Preheater Set PHS-1KB / PHS-2KB / PHS-9KB - Total weight: 4.9 kg (10.8 lb) - Ambient Operating Temperature: 10-40ºC (50-104ºF) PHS-1B 120V. Input 120V 50/60Hz Fuse 8A PHS-2B 230V. Input 230V 50/60Hz Fuse 4A PHS-9B 100V. Input 100V 50/60Hz Fuse 8A - Weight: 2.9 kg (6.4 lb) - Dimensions (Heater Unit): 195 x 288 x 41.5 mm - Maximum Power: 500W...
Seite 13
Cable de red ..........1 unit Ref. PHS-SA Ref. 0009417 (100V/120V) 0009401 (230V) Kapton Tape Thermocouple Manual ......1 unit Cinta Kapton ....1 unit Termopar ...... 1 unit Ref. 0017155 Ref. PH217 Ref. PH218 w w w.jbctools.com Ref. CLMB-A IR Preheater Set PHS-KB...
Características Heater Unit Unidad calefactora Área calefactora Zona B Fijadores para el Zona A soporte PHS-SA Entrada Conector de Red de Red Conexión Conexión para pedal (opcional) a la Consola Console Unidad de Control Consola Conector USB-B para PC: - Actualizar el programa de la Unidad de control Termopar (Tipo K)
Seite 15
w w w.jbctools.com IR Preheater Support Abrazaderas Soporte para Precalentador IR Para fijar en el soporte los PCBs de forma irregular. Para fijar PCBs idénticos en la misma posición. Ajuste de altura El soporte PHS-SA permite ajustar 3 alturas entre el PCB y el área calefactora. 28mm ·...
Seite 16
JBCset profiles (Perfiles JBCset) Hay 3 perfiles predefinidos por JBC: A, B y C. La diferencia entre ellos es el número de pasos: 2, 3 o 4. Cuanto más grueso sea su PCB y más capas contenga, más pasos serán necesarios para obtener un calentamiento uniforme y progresivo.
Seite 17
w w w.jbctools.com Recomendaciones 1. Coloque el Termopar tan cerca como sea posible del componente a trabajar. Cinta Kapton para fijar el Termopar en el PCB Termopar Auxiliar (TC) 2. Si hay algún componente sensible, use el Termopar Auxiliar como protección. Puede seleccionar la temperatura de protección en el menú...
Seguridad Es necesario seguir estas directrices de seguridad para proteger su salud y prevenir cualquier choque eléctrico, heridas, fuego o explosiones. - No utilice la unidad para otros fines que no sea el precalentamiento de PCBs. El uso incorrecto puede causar fuego. - El cable de red debe enchufarse en bases homologadas.
Seite 21
- Rango de temperatura: 50-250°C (120-482ºF) - Medición de temperatura: Termopar Tipo K - Perfiles predefinidos por JBC (JBCset): 3 perfiles (2, 3, 4 pasos) - Perfiles de usuario: 20 (hasta 6 pasos para cada uno) - Tiempo de trabajo máximo: 600 min o indefinido PHS-SA - Peso: 2 kg (4.4 lb)
Eigenschaften Heater Unit Vorheizgerät Heizzone Zone B Befestigungselemente Zone A für PHS-SA Halter für IR-Unterheizung Netzanschluss Netzschalter Steckanschluß für Steckanschluß für Pedal Konsole Console Steuereinheit Konsole USB-B Anschluss zum PC: - Zum aktualisieren der Steuereinheits-software Thermoelement (Typ K) Eingang für Hilfsthermoelement (Typ K)
w w w.jbctools.com IR Preheater Support Schlitzklemmen Halter für IR-Unterheizung Verwendet, um unregelmäßig geformte Leiterplatten im Halter zu fixieren. Verwendet, um identische Leiterplatten in der selben Position zu fixieren Höhenverstellung Der PHS-SA ermöglicht es drei unterschiedliche Höhen zwischen PCB und Heizfläche einzustellen. 28mm ·...
JBCset Profiles (JBC vordefinierte Profile) Es gibt 3 vordefinierte JBC Profile: A, B und C. Der Unterschied zwischen ihnen ist die Anzahl der Stufen: 2, 3 oder 4. Je dicker Ihre Leiterplatte ist und je mehr Schichten enthalten sind, desto mehr Stufen sind notwendig, um eine allmähliche Erwärmung zu erhalten.
w w w.jbctools.com Empfehlungen 1. Bringen Sie das Thermoelement so nah wie möglich bei der zu bearbeitenden Komponente an. Kapton-Band, um das Thermoelement (TC) auf der Leiterplatte zu fixieren Hilfsthermoelement (TC) 2. Wenn es ein besonders empfindliches Element auf der Leiteplatte gibt, benutzen Sie ein zusätzliches Hilfsthermoelement um dieses Bauteil zu schützen.
Sicherheit Es ist zwingend notwendig den Sicherheitsrichtlinien zu folgen, um die Gesundheit zu schützen und Stromschlägen, Verletzungen, Brand oder Explosionen vorzubeugen. - Setzen Sie das Gerät nicht für einen anderen Zweck als zum Vorwärmen von PCB´s ein. Falsche Verwendung kann Brand verursachen. - Das Netzkabel darf nur in zugelassenen Steckdosen eingesteckt werden.
Seite 51
w w w.jbctools.com Exploded View · Despiece · Explosionszeichnung · 分解組立図 · 分解图 51 51 51...
Seite 52
Warranty Garantía Garantie JBC’s 2 year warranty covers Esta garantía de 2 años cubre Die 2-Jahres-Garantie von JBC this equipment against all este equipo contra cualquier ersteckt sich auf das Gerät bei manufacturing defects, including defecto de fabricación, Herstellungsfehlern, einschließlich the replacement of defective incluyendo la sustitución de partes...