Box Content - Pingi CASCADA CHD-W6000D Betriebsanleitung

EN
CHD-W6000D - ULTRASONIC HUMIDIFIER

BOX CONTENT

HUMIDIFIER
CHD-W6000D
PARTS
Tank cover
Tank handle
Base
INTENDED USE
Your new Pingi Cascada humidifier CHD-W6000D is suitable for humidifying the air in enclosed indoor spaces.
The appliance operates on 220-240V, 50Hz (mains electricity). Never try to connect the device to other
power sources. Please always follow the safety instructions in this manual. Keep this instruction manual in
a safe place so that it is available at all times. This product complies with regulatory, national and European
requirements. Never try to make technical modifications to this device. We do not accept liability for accidents
or damages resulting from failure to follow these operating and safety instructions.
WHAT TO EXPECT
The Pingi Cascada humidifier CHD-W6000D is an ultrasonic humidifier that atomises water. High-frequency
vibrations transform up to 300 ml (±30ml) of water per hour into a fine mist. This means it will increase
the humidity level in the air by generating millions of small droplets. The device has a 6L tank. The CHD-
W6000D has multiple speed settings and can automatically maintain the ambient humidity level you select.
Humidifiers need to be cleaned regularly to prevent limescale build-up or biofilm formation. Please refer to the
cleaning section for further information.
BEFORE YOU START
Please carefully read the safety instructions on the front page of this manual before getting
started.
PLACEMENT AND INSTALLATION
1. Select a level surface that provides sufficient distance between the humidifier and any
walls and other objects. Please mind that some water may escape from the base or
tank when installing the tank. Do not place the device on or near moisture-sensitive
objects or surfaces.
2. If needed, install the included filter cartridge in the appropriate slot in the base.
3. If needed, install a CR2025 battery in the remote control.
4. Plug in the device.
We recommend using this appliance in rooms with a room temperature of 18 - 22 °C
REMOTE CONTROL
INSTRUCTION
MANUAL
Mist nozzle
Water
tank
LCD
panel
FILLING THE TANK
1.
2.
3. You can change the direction of the mist output by rotating the mist nozzles.
4. You can add water at any time without removing the tank from the base.
SWITCHING ON THE HUMIDIFIER
The humidifier can be switched on and off with the ON OFF button on the device, or the ON OFF button on
the remote control. After switching on the appliance, the display will show the current power setting (3) and
the current ambient humidity percentage. Use the MIST button to select the desired power setting (1,2,3).
Selecting a lower power level will adjust the amount of mist produced.
SETTING A HUMIDITY PERCENTAGE
When switched on, the device will be in CONTINUOUS MODE. This means it will continue to output mist until
the tank is empty. The current ambient humidity level will be visible on the LCD panel. If desired, you can set a
humidity level from RH 40% to RH 90% by using the HUMIDITY button. The humidifier will try to maintain the
selected humidity level and pause humidification until the measured ambient humidity percentage drops below
your selected level. To go back to CONTINUOUS MODE, you can either switch the device off and on or select the
setting after RH 90% by using the HUMIDITY button again.
Tip: RH 60% is considered a comfortable humidity level for human beings.
OUT OF WATER SIGNAL
The humidifier will automatically switch off when it detects that the tank is empty. Three intermittent beeps
will sound and the red TANK symbol will flash. The appliance will then shut down. Fill the tank to resume
operation.
TIMER FUNCTION
The timer function allows you to switch on the humidifier for a set number of hours. The appliance will
automatically shut down after the set time has passed. Use the TIMER button on the remote to set the timer
to 1-8 hours.
NIGHT MODE
NIGHT MODE can be activated to automatically dim the display when you are not operating the device. Press
the NIGHT button and the LCD display will light up for 5 seconds and then dim. The display will now only be
activated when you operate the device. Press any button to activate the LCD display for 5 seconds. Press any
button while the LCD is still activated and NIGHT MODE will be deactivated.
CLEANING
Both the tank and base need to be cleaned regularly.
We recommend cleaning the appliance once a week.
Important notices:
- Make sure the device is unplugged when cleaning it.
- Do not pour hot water in the tank.
- Do not use detergents or chlorine.
- Use vinegar or a coffee machine descaling fluid.
Procedure:
Water tank: Empty out the water tank. Rinse the water tank with cold water and some vinegar (1 cup).
Optionally use a soft brush. Thoroughly flush the tank after emptying out the vinegar solution.
Base: Empty out the base. Use a microfibre cloth with some cold water to clean it.
Filter cartridge: Rinse the filter cartridge with hot water. Optionally soak the filter several minutes in hot
water.
Empty and flush the
Place the filled tank on the base and replace the tank