VOLTCRAFT 2264184 Gebrauchsanweisung Seite 2

Operating Instructions
Power Pack (12 V / 1500 mA)
Item No. 2264184
Intended use
The power pack serves as voltage supply for low-voltage devices with matching DC jacks. It
is intended for connection to common household mains voltage (100 - 240 V/AC, 50/60 Hz). A
galvanic separated DC voltage is applied to the output. The power consumption of the consum-
ing device many not exceed the nominal voltage of the respective power pack (depends on the
type). The product has a protection against short circuit and overload.
This product fulfils European and national requirements related to electromagnetic compat-
ibility (EMC).
Unauthorised conversion and/or modification of the device are inadmissible because of safety
and approval reasons. Any usage other than described above is not permitted and can damage
the product and lead to associated risks such as short-circuit, fire, electric shock, etc. Please
read the operating instructions thoroughly and keep them for further reference.
Delivery content
• Power pack • Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of symbols
The symbol with the exclamation mark in the triangle is used to indicate important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
This symbol indicates that the product meets the energy efficiency requirements for
Class VI.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting per-
sonal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dan-
gerous playing material for children.
• Protect the appliance from extreme temperatures, direct sunlight, strong jolts,
high humidity, moisture, flammable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Consult an expert when in doubt about the operation, safety or connection of
the appliance.
• Maintenance, modifications and repairs must only be completed by a technician
or an authorised repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
• Never switch the device on immediately after having taken it from a cold to a
warm environment. Under adverse conditions, the resulting condensation could
destroy the device. Allow the device to reach room temperature before switching
it on.
• Power units are not designed for application to human beings or animals.
Operation
Periodically check the technical safety of the device, e.g. check for damage to
the housing etc.
Always lay the cable so that nobody can trip over or become entangled in it.
This poses a risk of injury.
1. Connect the DC plug of the power pack with the DC jack on the low-voltage device.
2. The polarity cannot be altered. The plug has the fixed polarity „inside plus (+), outside
minus (-)".
3. Make sure that the consumer is switched off when connected to the power pack.
4. Plug the power pack into a standard domestic wall socket. Correct operation is signaled at
the power pack by a LED.
5. To remove the consumer, proceed in reverse sequence.
Troubleshooting
By purchasing the power pack you have acquired a product that has been designed to the state
of the art and is operationally reliable. Problems and malfunctions can occur nevertheless. We
would therefore like to show how you can rectify certain faults yourself:
Problem Cause
No mains voltage.
The power indicator
is not lit.
Power pack over-
loaded.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the house-
hold waste. At the end of its service life, dispose of the product in accordance with
applicable regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the envi-
ronment.
Technical data
Input voltage ................................. 100 - 240 V/AC
Input AC frequency ....................... 60/50 Hz
Output voltage .............................. 12.0 V/DC
Output current ............................... 1.5 A
Output power ................................ 18.0 W
Average active efficiency .............. 86.2 %
Efficiency at low load (10%) ......... 78.4 %
No load power consumption ......... 0.10 W
Operating conditions ..................... 0 to +40 ºC, 20 – 85 % RH (non-condensing)
Storage conditions ........................ -20 to +60 ºC, 10 – 90 % RH (non-condensing)
Dimensions (W x H x D) ............... 51 x 73 x 82 mm
Weight .......................................... 140 g
Model identifier:
Commercial registration number:
Manufacturer:
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
Solution
Check the circuit breaker of the power outlet.
Check the correct fit of the power outlet.
Remove the consumer and check the techni-
cal data.
FPPS 12-18W-N
HRB 3896
Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau
*2264184_v1_0620_02_dh_m_en