SUNTEC Home Essentials BBQ-9479 Bedienungsanleitung Seite 11

with right hand whilst lift the tube for wheel (III) upward with left hand. Then locate the tube(III)
with the orientation tube which under the side table. The trolley frame is standing up now. Fold
up the trolley : First , step on the middle of support tube (I) with right foot , hold up the side
table (II) with right hand whilst your left hand holds the short edge of support tube(III) and place it
down slowly . Attention : When folding up the trolley , DON'T hold the two sides of tube (III)
to avoid any pinch to your hand.
6. After standing up the trolley frame, you MUST set the safety locking unit (f) immediately. This
safety locking unit is with self-locking feature. Press the spring (e) and hook the bent hook(f) on
the extension part (e). Then stop pressing the spring and it will retract to lock the safety hook unit
automatically.
Attention : Make sure the safety hook unit is LOCKED during cooking or moving. DO NOT
try to turn or pull the safety hook while using this appliance.
7. Firstly, remove the screw from the trolley tube (II). Then, install the stand tube (G1) onto the
trolley tube (II). and installthe stand tube (G2) onto the trolley tube (II). There is a positioning hole
(IV) on the stand tube (G2), which is going to fix the bottom positioning projection of base . Tighten
the stand tube (G1 and G2) and trolley with screws and nuts.
8. Set the bowl-shaped base (h) into the stand tube (g) to the bottom. Fix the bottom positioning
projection of base into the positioning hole (IV). When remove the base from stand tube (g),
please step slightly on the supporting tube (I),hold the handles of base and take it off.
9. Insert the grease collecting cup (j) into the bracket supplied for it in the back of bowl-shaped
base (h) of the appliance. In order to fix it well, please buckle the hole on grease collecting cup into
the positioning projection which is in the middle of the bowl-shaped base. (Tips: This grease cup
can be filled with little water to make it more easier to clean). To get the grease collecting cup out,
please give it a slight press, after depart the hole from the positioning projection,
you can take it out easily. Attention : The capacity of grease cup is 0.3L , please pour out the
grease once it's full.The surface of grease cup is HOT . Please well protect yourself if
needed to touch it while cooking !
10. Place the grill plate (K) on the base of the appliance (H). Firstly, insert the heating tube socket
(L) of grill plate into the protective hole (M) intended for it slantways . Secondly, set the grill plate
horizontally on the appliance base.To take grill plate off, please hold up the right side of the plate
and take the pull socket (L) out of the protective hole(M) slantways. Before take the grill plate out,
make sure it is cool and not in use.
Attention: The grill plate must be used together with
bowl-shaped base!
11. Insert the detachable temperature regulator's pin(n)into the heating tube socket (L) , it can plug
in the appliance. When remove the detachable temperature regulator, please hold the handle of
the base to avoid pushing over the
appliance.Attention: Please take care DON'T be tripped over by the power cord when operating the
appliance. Remember to remove the plug after use.
12. Install the cover. Holds the cover handle (p) and insert the metal hinges (O) into the
installation holes (Q)
of base. When remove the cover, please open the cover and tilt to 45° between cover and grill
plate , and detach out the metal hinges(o) from installation holes (Q). Other angles can't help to
detach the cover but only around 45° .
13. The design of clamshell function and detachable of this cover makes it more convenient for
using and cleaning. Attention: If user want to close or open the cover , please hold the cover
handle. Mind yourself not be burnt
as the metal cover is HOT while cooking.