Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN
that the surrounding- and rainwater can seep away. It would be ideal if
system.
Installation
pump consists of the following parts:
1. Pump
2. Valve
3. Seal (O-Ring)
4. Clamping ring
5. Vessel
6. Central pipe
7. Filter screen
8. Drain plug
9. Centralizer (cover for standpipe)
10. Base plate
11. Pressure hose
Filter vessel
1.
2.
make sure that the stand pipe is located in the middle of the boiler
and that the drain plug is screwed in.
3.
Now put the centralizer on the tank opening, while centering the
standpipe. (Illustration 4)
4.
(Illustration 4)
5.
Then mount the top of the boiler or the valve head and the boiler
neccassary to clean again and wash off any sand or accumulated
debris. The connection of the top of the boiler or the head valve with
ring is screwed with the clamping ring screw and the collet nut.
(Illustration 5 & 6)
6.
7.
The pressure gauge (if included) is screwed to the side of the 7-way
(Illustration 9)
Pump hose connections (Illustration 7)
1.
Skimmers: Connection from skimmer to the front connector of the
2.
Pressure line: Connection going from the upper area of the top of
7-way valve.
3.
Return line: Connection from the 7-way valve with the designation
„RETURN" to the connection at the inlet nozzle (pool). Secure all
connections with hose clamps.
4.
Backwash: Connection „WASTE" (Empty) in the channel.
Connections are made with special pool hoses and hose clamps!
Filter system installation instructions
these particles will end up in your pool. To clean the sand, please follow
the instructions below:
FILTRO A SABBIA
SMP214
Do not plug the system in until advised to do so below.
■ Make certain the pump is not plugged in to a power supply.
■ Ensure that the valve lever is in the "closed" position.
■
water level. The hose connections must also be correctly connected
and fastened.
■
the water level is at least 2,5 – 5 cm above the top of the hose intake
(Skimmer) and return ports in the pool.
■ Release the shut off valve at the intake port (Skimmer) in the pool. If
you plugged the intake port (Skimmer), remove the plug to allow the
■
system.
■
■
■
if necessary. Leakage points may possibly arise due to manufacturing
the connections before the connection hose is attached.
■ Follow the backwash process described below.
Backwash Prozess
■ S Disconnect the Motor/Pump from the Power Source.
■ Attach backwash hose (not included) to backwash port.
■ Place the Multi-Port Valve in the "Backwash" position.
■ Reconnect to power source.
■
■ Disconnect the Motor/Pump from the Power Source.
■ Place the Multi-Port Valve in the "RINSE" position.
■ Reconnect to power source.
■
from pump and valve.
■ Disconnect the Motor/Pump from the Power Source.
■ Place the Multi-Port Valve in the "Filtration" position.
■ Reconnect to power source.
■
Filter operations
Setting
Filters
this position, water is directed through the top of the
Contaminants are trapped by the sand as water makes
to the pool.
Rinse
bed. This should always be done immediately after
container in this position, and the valve is rinsed whilst
the water runs off via the waste pipe.
Cirkulation
Function: circulate water after chemical treatment.
This position is used during certain pool cleanups and
chemical treatments when you don't want the water
contaminating the sand. In this position, water is only
directed through the valve back to the pool and does
pagina 9 di 18
Werbung
Inhaltsverzeichnis
