Service And Special Functions - Grundig Tharus 26 LW 68-9510 Dolby Serviceanleitung

GRUNDIG Service GRUNDIG Service

Service and Special Functions

Call up the Service Menu:
Call up the dialogue line:
Changing the setting in the dialogue line:
Back to previous menu:
Exit menu:
Service menu for retailer (code number): "8500"
1. Switching-on Options
1.1 ATS Reset
Press mains button "ON" while holding down the "
remote control.
– The basic analogue values are loaded.
– The ATS bit is set. When switching on the next time, this option
releases the ATS euro plus function. The current programme allo-
cation (channels) is cleared.
1.2 Electronic Programme Lock (parental lock)
Enter the key sequence
number.
1.3 Software Version Number
Call up the "EASY DIALOG" menu. Pressing the green button indi-
cates the software version number.
1.4 Flash Programming
Required equipment
Flash programmer F-Prog 1 / from version 2.0 on or
Service Toolbox part number 772004001200.
Required hardware
Pentium-PC, Microsoft Windows 95
– Free memory of 32MB
– CD-ROM drive
– COM port
– Internet access
1.5 Direct Display Type Adjustment
If the menus can not be displayed any longer due to an incorrect
display type adjustment, you can carry out the correct adjustment
with the help of key short cuts.
Before and after the direct entry, the unit must be switched off and
on again!
The " i ", "red" and numeric keys select the desired display type ac-
cording the display lable.
The following digits indicate the display types:
1 SAM LTA260W2
2 AUO T260XW01
3 LPL LC260W01
4 CMO V270W1
5 CMO V296W1
6 AUO T296XW01
7 LPL LC300W01
8 LPL LC230W01
2. Special Functions in the "Installation" Menu
2.1 Entry of Letters
Call up the "Letter entry" menu via "EASY DIALOG" –> "Installation"
–> "Special functions".
You may select between "Off", "On" and "Mix" for the programme
selection letter entry.
2.2 Visible or Unvisible "Sound scale" for all Programmes
Call up the "Sound scale" menu via "EASY DIALOG" –> "Installati-
on" –> "Special functions".
With "Off" selected, no volume bar is displayed.
2.3 Switching on with Programme "1" or automatically
Call up the "Switch on" menu via "EASY DIALOG" –> "Installation"
–> "Special functions" .
Set the option "Preset 1" or "Automatic".
With the "automatc" setting, the programme position selected when
switching off is selected again when switching the set on again
(Last station memory).
Downloaded from www.Manualslib.com
Button " i " (EASY DIALOG)
Buttons "P+" / "P-" –> "OK"
Buttons " " / "
Button "Blue"
Button " i "
" button on the
"7 0 3 8 5 8 0" to cancel your personal code
manuals search engine
2.4 "Megalogic Info" (only if a connected Megalogic set is identified)
Call up the "Megalogic info" menu via "EASY DIALOG" –>
"Installation" –> "Special functions".
The Megalogic control can be switched to "On" or "Off".
2.5 Status Display
" –> " OK "
Call up the "Status display" menu via "EASY DIALOG" –>
"Installation" –> "Special functions".
You may select the position (top or bottom) where the information
about the sound mode and the picture format is displayed.
With the "Off" option, no information is displayed when changing the
programme.
2.6 Automatic Volume
Call up the "Automatic volume" menu via "EASY DIALOG" –>
"Installation" –> "Special functions".
In the "On" position, the sound IC regulates the volume internally
to the normal value (e.g. increased deviation in the case of adverti-
sing).
2.7 Noise Reduction P1-P...
Call up the "Noise reduction P1-P..." menu via "EASY DIALOG" –>
"Installation" –> "Special functions. For the programmes 1-P... you
may set the noise reduction to "off", "low" or "automatic".
2.8 Picture Sharpness P1-P...
Call up the "Sharpness P1-P..." menu via "EASY DIALOG" –>
"Installation" –> "Special functions".
The picture sharpness is set for all programmes.
2.9 Colour Match
Call up the "Colour match" menu via "EASY DIALOG" –> "Installati-
on" –> "Special functions" –> page 2.
The colour match (luma delay) is set for every programme.
2.10 Automatic Format
Call up the "Automatic format" menu via "EASY DIALOG" –> "In-
stallation" –> "Special functions" –> page 2.
You can select which picture format (4:3, 14:9 Zoom or Panorama
Zoom) is shown for programmes without letterbox and without trans-
mitted WSS info (Wide Screen Signaling) and with an automatic pic-
ture format.
3. Service Settings for the Retailer
3.1 Picture Settings
3.1.1 White Balance
Call up the "White balance" menu via "EASY DIALOG" –> "Installa-
tion" –> "Dealer service menu" –> Code number "8500" –> "Picture
settings".
Adjust the values for "red", "green" and "blue" so that a white picture
is obtained (see Alignment, Point 5).
3.1.2 Switching the Blue Screen Background On and Off
Call up the "Blue screen" menu via "EASY DIALOG" –> "Installati-
on" –> "Dealer service menu" –> Code number "8500" –> "Picture
settings".
Select "On" or "Off".
3.2 Hardware Equipment
3.2.1 Display Type
Call up the "Display type" menu via "EASY DIALOG" –>
"Installation" –> "Dealer service menu" –> Code number "8500" –>
"Hardware equipment".
Select the appropriate display type.
3.2.2 Tuner Type
Call up the "Terrestrial tuner" menu via "EASY DIALOG" –> "Instal-
lation" –> "Dealer service menu" –> Code number "8500" –> "Hard-
ware equipment".
Select the appropriate tuner type.
1 - 9 1 - 9
Chassis G1 Chassis G1