Reflecta COSMOS+RF Betriebsanleitung Seite 2

INSTALLATION
MANUAL
INTRODUCTION
ENGLISH
Thank you for purchasing the motorized projection screen. This screen is made entirely in Europe with first-class materials, including a high quality
projection surface to guarantee excellent performance for your installation.
WARNINGS
Before installing the screen, please read the following instructions carefully. We would recommend that these instructions are stored safely for future
reference. The manufacturer does not take responsibility for any damage to property or personal injury if the screen is used outside of recommended
specifications or in case of incorrect/poor quality installation.
CERTIFICATIONS
Motorized screens are certified.
The surfaces for projection used on the products are cadmium-free and are fire-proof certified as follows:
- class M1 – MATTE WHITE, LUMI-GREY, REAR PLUS
- class B1 – WHITE, MICROPERFORATED
- class 1 – CINESOUND, FRONTREAR
WARRANTY
This projection screen is guaranteed 2 years from the purchase date for manufacturing defects.
Responsibility is limited to repairing or substitution of the defected components and without any other charge at our expense.
Warranty is officially voided if the screen has been dismantled or it is returned with collision damage or defective due to incorrect installation. Repairs
must be carried out by an Approved Screen International Certified Engineer.
Warranty is officially voided if:
1) the motor is removed / dismantled;
2) the screen has been transit damaged;
3) the instructions regarding the electrical connections have not been followed;
4) the products have to be installed following the electric regulations (CEI) and the other local specific laws;
5) electrical accessories have been used that are incompatible with the screen motor causing damage to its internal components;
6) the motor end stops have been modified without the authorisation of the factory;
7) the sticker regarding the serial number of the product has been altered, deleted, removed or is illegible.
DO NOT install this screen nearby or over heating or air conditioning systems, because PVC is a plastic material which dilates and remains damaged if it
is subjected to heat and/or cool air.
DO NOT install this screen either facing direct sun light or blocking a window as PVC could be damaged for the explanations given above.
The PVC cloth is very sensitive to temperature range.
We advise you to wait 2 hours for the screen to acclimatise before using the screen after delivery, especially if screen is brought into a warm
environment from cold.
DO NOT WASH the projection surface with alcohol or solvent nor with commercial cleaners. Every now and then dust the surface with a dry and clean
duster.
Please, be very careful because any kind of stain on the PVC cloth is inerasable.
The screen has to be used showing the total projection sizes indicated on the packaging; therefore it is NOT allowed to adjust the end stops to restrict
the total drop or extend it. Restricting the total drop of the screen is likely to cause your screen surface to lose its flatness.
The manufacturer will not accept returns of screens for repair without manufacturer's authorization (RMA number) and without a suitable packaging.
INSTALLATION INSTRUCTIONS
ASSEMBLY
Our screen is supplied with ceiling/wall brackets suitable for fixing it on the wall or ceiling by heavy duty bolts that are supplied in the packaging
(Fig. 1).
WARNING: DO NOT INSTALL THE SCREEN NEAR HEATING SOURCE BECAUSE IT DAMAGES THE PROJECTION SURFACE. Prior to installing the roller screen,
ensure the ceiling/wall is suitable for the loading induced by the weight of the screen. Take particular care if the construction is timber or stud
partitioning. If in doubt, seek the advice of a structural engineer. Please be aware that the screen is heavy and two or more people may be required to
lift it safely. Fix the brackets to the wall/ceiling, insert the clamp screws into the threaded holes on the front of the fixing brackets, hook roller case in
tab on bracket and tighten the clamp screws to the front groove to lock the screen in position (Fig. 2). Release the screen transport straps. Cut and
release the screen from the ribbon that keeps the bottom bar tightened. At the end of the installation, please check that the motorized screen is
perfectly level.
1. ELECTRIC CONNECTION
Connection of the power supply must be carried out by qualified personnel only. The line connection to the electric motor is the usual connection,
brown - phase, blue -neutral, yellow-green - earth. The fourth black wire has not to be connected.
The screen is equipped with a radio remote control that has three keys: upper arrow indicates up, down arrow indicates down, middle key – stop.
(Fig. 3)
IN CASE OF MAINTENANCE, UNPLUG THE POWER SUPPLY.
In case the screen is controlled via relais, take care that the control system is programmed so there is no tension on the relais for at least 1 sec. during
switching between rolling up and rolling down operations and viceversa.
IT IS FORBIDDEN TO STAY UNDER THE PROJECTION SCREEN.
IT IS FORBIDDEN TO USE THE PROJECTION SCREEN OUTDOOR.
COSMOS N + RF