Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating instructions
Universal tablet stand for 7.9–10.1 inch tablets
Item no. 1483524
Intended use
This height-adjustable stand is designed for tablets with a display size of 20.1 cm (7.9") to 25.7 cm (10.1").
It consists of an elegant aluminium pole with a built-in cable guide on the back and a sturdy steel base.
The stand comes with a clamp holder that locks your tablet in place to protect it against theft. The angle of
the bracket can be adjusted. The clamp holder is designed to cover the home button to prevent guests or
customers from using the tablet. The product is intended for indoor use only. Do not use it outdoors. Contact
with moisture, e.g. in bathrooms, must be avoided under all circumstances. For safety reasons, you must not
rebuild and/or modify this product. Using the product for purposes other than those described above may
damage the product.
Read the instructions carefully and keep them. Make this product available to third parties only together with
its operating instructions.
Delivery content
• Pole
• Clamp holder
• Base
• Plastic pad
• 2 x EVA pads
• Lock with key (2x)
• M5x8 screw (tamper-proof)
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the
QR code above. Follow the instructions on the website.
Explanation of symbols
The symbol with the exclamation mark in the triangle is used to highlight important information
in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) General information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity
and moisture.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• Consult an expert when in doubt about the operation, safety or assembly of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
b) Mounting
• Check the contents of the packaging before mounting the product. You will not be able to
mount the stand unless all components are present.
• Mounting the product in an unsuitable location can result in injury or damage to property!
• Proceed with care when assembling and mounting the product! The product has some sharp
edges which have the potential to cause injury!
• Only carry out the work necessary to mount the product. Never attempt to modify or repair
the product.
• Work on a clean, soft and dry surface. Protect valuable furniture using a suitable pad or cloth.
• Do not overtighten the screws. This may damage the threads and reduce the strength of the
fitting.
• Ensure that the tablet's cables will not become trapped or bent.
• Check that all the screws are securely in place from time to time. The screws may become
loose over time as the product is moved around.
• 4 x M6x16 screws
• 4 x ST5.5x50 screws
• 4 x concrete anchors
• T40 Torx key
• T25 Torx key
• Operating instructions
• Manufacturer's instructions
• Do not overload the stand. Refer to the technical data for information on the load capacity.
Do not hold onto the tablet stand or use it to support yourself. Do not secure any objects to
the tablet stand other than a tablet.
• If you are in any doubt about how to assemble the product, ask a technician to assemble it
for you.
• Do not attach the stand to unsuitable floor surfaces. Thin or laminate flooring is normally
unsuitable. However, special parts are sometimes available for these types of surfaces. If in
doubt, contact a specialist before mounting the product.
• Mounting materials (such as screws and dowels) may vary depending on the mounting
surface. The dowels and screws that are included with the product are only suitable for
solid floors. Special dowels and screws are not included and must be purchased separately
depending on your floor type.
• Plan the mounting location carefully so that the tablet stand will be located in the desired
position once you have finished mounting it.
• Ensure that no underfloor cables or wires are damaged during drilling/screwing. Accidentally
drilling into electrical cables can cause a fatal electric shock!
• Always pay attention to your safety when working with electrical tools (such as a drill).
Refer to the safety information in the corresponding instructions.
• Ensure that no unauthorized persons are present in the assembly area when mounting the
product.
Assembly
The following instructions are designed to be used in combination with the images in the manufacturer's
instructions.
Figure 1
• Secure the pole (A) to the base (C) using the plastic pad (F) and four M6 screws (E). Use a suitable Phillips
screwdriver to tighten the screws.
Figures 2 a & b
• Decide where you want to mount the stand. Mark the positions of the drill holes on the mounting surface.
Use the base (C) as a template.
a) If you are mounting the stand on a wooden surface, drill the necessary holes.
b) If you are mounting the stand on a concrete, stone, or tiled floor, drill the necessary holes and then
insert the concrete anchors (J).
• Secure the base to the floor using the four ST5.5 screws (I). The non-slip rubber feet should face
downwards.
Figure 3
• Place one or two EVA pads (H) onto the front of the clamp holder (B) (this will depend on your tablet
model).
Figure 4
• Place the clamp holder on a level surface (e.g. a table).
• Hold down the small lever on the bottom of the holder and extend the side clamps.
• Pull the top clamp upwards.
Figure 5
• Place your tablet into the clamp holder.
• Slide the side clamps together until they sit tightly against the edges of the tablet.
Figure 6
• Slide the top clamp to the edge of the tablet so that it locks the tablet in place.
Figure 7
• Ensure that the holes in the vertical clamp and the clamp holder are aligned, and then insert the lock (D).
• Insert the key into the lock and turn it clockwise to secure the lock in place. To remove the lock, insert the
key into the lock and turn it anticlockwise.
Figure 8
• Secure the clamp holder to the pole using the M5 screw (G). Use the T25 Torx key (L) to tighten the screw.
• To adjust the angle of the clamp holder, use the T40 Torx key (K) to loosen the screw on the side of the pole
clamp. Once you have adjusted the angle, tighten the screw to lock the clamp in place.
Figure 9
• As shown in the diagram, the clamp holder can be rotated 360º and tilted 140º.
• You can run the tablet cable through the cable guide on the back of the pole.
Maintenance and cleaning
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these could damage the
casing or even impair the functioning of the product.
• Use a dry, lint-free cloth to clean the product.
Technical data
Load capacity ....................................... 1 kg
Operating/storage conditions ................ -30 to +80 °C, 1 – 80 % relative humidity (non-condensing)
Base dimensions (W x D) ..................... 315.5 x 217 mm
Pole height ............................................ 330 mm
Weight .................................................. 2.02 kg
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE.
*1483524_v2_0317_02_DS_m_(1)_4L
Werbung
