Herunterladen Diese Seite drucken

Werbung

INSTALLATION INSTRUCTIONS
Technical Data
1
0.4
Nm
3
2
Fig. 1 Serial connection /
Backup fuse / Vorsicherung
Durchgangsverdrahtung
F
*)
L
PE /
N
DEHNrail modular
E
Type: DR M 2P XXX (FM)
Electronic
device
F
*)
in TT-System
I∆
RCD / FI
with RCD! /
mit FI-Schutzschalter!
Coordination / Koordination
DIN VDE 0185-305-4: ...
IEC 62305-4: ...
LPZ 0
LPZ 1
LPZ 2
A
DEHNrail modular
DR M 2P XXX (FM)
Class I
Class II
Class III
Type 1
Type 2
Type 3
DEHNrail modular
press
1
DR M 2P XXX (FM)
2
Size 0
Class III
IEC 61643-1/-11: ...
Type 3
EN 61643-11: ...
1
press
Fig. 2 Parallel connection /
Stichverdrahtung
*)
F1
L
PE /
N
F2
F ≤ 25 A gL / gG
o.k.
F > 25 A gL / gG
*)
in TT-System
I∆
RCD / FI
see Fig. 2
with RCD! /
Parallel Wiring
mit FI-Schutzschalter!
Fault indication / Defektanzeige
LPZ 3
Technical data / Technische Daten
Application: for control circuits only/
Anwendung: nur für Steuerkreise
Typ
30
60
75
U
30 V
60 V
75 V
c
max. 25 A
gL/gG (B 25 A)
ϑ° C
-40°C ... + 80°C
IP-Code
20
10 mm
min. 1,2,3,4,
0.5 mm²
max. 1,2,3,4
2.5 mm²
Backup fuse / Vorsicherung
E
Electronic
DEHNrail modular
device
Typ: DR M 2P XXX (FM)
F1 >25 A gL / gG
F1
F2 ≤ 25 A gL / gG
press
F1 ≤ 25 A gL / gG
F2
F2
Protection Module
DR MOD XXX
press
green
ok
12
11
14
Remote Alarm
test
Terminal
ok
green
12
11
14
replace
red
Protection Module
12
11
14
DR MOD XXX
Publication No. 1557 / UPDATE 11.12 Id. No. 065997
Basic circuit diagram / Prinzipschaltbild
1
ϑ
150
255
150 V
255 V
12
11
14
10 mm
3
4 mm²
Cable routing / Kabelführung
ok
IN (OUT)
OUT (IN)
Remote signalling contact / Fernmeldekontakt
DEHNrail modular DR M 2P XXX FM
U
/ I
N
N
AC:
250 V / 0,5 A
DC:
250 V / 0,1 A
125 V / 0,2 A
75 V / 0,5 A
12
11
14
max. 1,5 mm²
© COPYRIGHT 2012 DEHN + SÖHNE / protected by ISO 16016
2
ϑ
4
!
IN (OUT)
OUT (IN)
p.t.o.
Safety
Instructions

Werbung

loading

Inhaltszusammenfassung für Dehn DR M 2P Serie

  • Seite 1 75 V / 0,5 A green Class I Class II Class III Type 1 Type 2 Type 3 max. 1,5 mm² p.t.o. replace Protection Module Safety DR MOD XXX Instructions © COPYRIGHT 2012 DEHN + SÖHNE / protected by ISO 16016...
  • Seite 2 Use a local equipotential bonding bar if possible. For proper operation the SPD must be connected to a low impedance ground. Remote Contact Signaling: In case of a device with remote contact signaling make sure that the torque is as indicated in the technical data. Problem Diagnostics: If there should be any problem please contact your local DEHN representative.

Diese Anleitung auch für:

Dr m 2p fm serieDr m 2p 30Dr m 2p 60Dr m 2p 75Dr m 2p 150Dr m 2p 255 ... Alle anzeigen