Program Overview - Novoferm tormatic T100 DES Montage- Und Betriebsanleitung

6

Program overview

Menu 3 Basic settings
Menu Entry Selection
item
30 Door setting of upper end position
Reversal of the direction (press for 5 s)
31 Door setting of lower end position
32 Door setting for 1/2 opening position
33 Fine correction of upper end position
50 Factory settings
50 - 0 0...80 mm lower
50 - 99 0...80 mm higher
34 Fine correction of lower end position
50 Factory settings
50 - 0 0...80 mm lower
50 - 99 0...80 mm higher
35 Selection of closing edge safety device
Measurement display (press 5 seconds)
0 Optical closing edge safety device OSE
(default setting)
1 Electrical safety edge 8K2
2 Pressure wave switch with testing
3 Electrical safety edge 8K2 with slack rope
switch
4 Wireless closing edge, RadioBand
36 Selection of photoelectric sensor
0 Without photoelectric sensor (default setting)
1 2-wire photoelectric sensor LS2
2 4-wire photoelectric sensor LS5 photoelectric
reflection sensor
3 Photoelectric sensor LS2, mounted in frame
4 Photoelectric sensor LS5 photoelectric
reflection sensor mounted in frame
5 2-wire photoelectric sensor LS2 with stop
function for opening
6 4-wire photoelectric sensor LS5 with stop
function for opening
37 Correction of pre-limit switch closing edge safety
25 Correction of pre-limit switch closing edge
safety (default setting)
25 - 0 0...50 mm lower
25 - 99 0...100 mm higher
- - Exit menu
Menu 4 Further door settings
Menu Entry Selection
item
40 Selection of operating mode
0 Dead man OPEN / dead man CLOSE
1 Pulse OPEN / dead man CLOSE
2 Pulse OPEN / pulse CLOSE (default setting)
3 AR - automatic closing
4 AR - with reduction of the hold-open time
5 Open/close operation, red/green light with
A800 (option)
6 As in 5, however, with reduction for
photoelectric sensor
26 - EN
Menu 4 Further door settings
Menu Entry Selection
item
41 Response to closing edge safety device
0 Full reversing (default setting)
1 Partial reversing
42 Overtravel correction
0 Off
1 On (default setting)
43 Floor adjustment
0 Off (default setting)
1 Advanced end stop by closing edge
2 Floor adjustment activated for 200 cycles
3 Floor adjustment activated for 1000 cycles
4 Permanent floor adjustment
44 Hold-open time in seconds
0 0 s (default setting)
1 - 30 1 s - 30 s (in increments of 1 s)
31 - 60 35 s - 180 s (in increments of 5 s)
61 - 99 190 s - 22.5 min (in increments of 30 s)
45 Status relay X5
0 Door close signal (default setting)
1 Door open signal
2 2-minute garage light
3 5-minute garage light
4 On/off with hand-held transmitter
5 ELTACO wipe pulse
6 Control of electronic door lock EDL100
(optional)
46 Status relay X6
0 Door close signal
1 Door open signal (default setting)
2 Red light without advance warning time
3-12 Advance warning time before closing 1 s -
10 s
13-22 Advance warning time before opening and
closing 1 s - 10 s
47 Spring fracture detection
Spring balance indication (press for 5 s)
0 Off (default setting)
1-99 Entry of spring force
48 Opening force limitation
0 Off (default setting)
1-98 Entry of switch-off force
99 Carry out weight measurement run with test
weight
49 Motor duty cycle
0 Without limitation (default setting)
1 Geared motor 5.24 (25 min / 35 %)
2 Geared motor 5.24 WS (25 min / 30 %)
3 Geared motor 9.15, 9.20, 9.24 (25 min / 60 %)
4 Geared motor 9.24 WS (25 min / 20 %)
5 Geared motor 6.65 DU (10 min / 35 %)
6 Geared motor 14.15 (25 min / 60 %)
- - Exit menu
T100 DES