Bron Broncolor Para 170 FB Montageanleitung

Mounting instructions for umbrella
Para 170 FB / Para 220 FB / Para Soft 220 FB / Para 330 FB
Mounting of the umbrella reflector
1. Fixing the umbrella reflector onto the stand
Take the umbrella out of the container.
-
Slide the tilt head onto the bolt which is situated on the reverse of the spoke framework rim, and tighten the screw.
-
Fix the folded umbrella horizontally onto the stand (image 1).
-
Remove the Velcro
-
Remove the protective ribbon which fits around the circular base holding the supporting spokes.
-
2. Unfolding the umbrella reflector
Tilt the umbrella reflector forwards (image 2).
-
With flat hands, gently press the umbrella spokes outwards (image 3).
-
3. Front focusing
The front focusing device cannot be removed by the user. It is an integrated part of the umbrella.
-
If required mount the extension adapter for the Para FF/FB (art. no. 33.476.00) on the lamp head holder of the
-
front focusing device.
4. Opening the umbrella reflector
To open the umbrella use the crank gear (image 4).
-
Insert the bar handle and screw it in tightly. This bar is enclosed with the umbrella and the user needs it as a
-
handle to change or modify the position of the umbrella (image 5).
Put the umbrella into the desired position.
-
5. Mounting of the Pulso G, Unilite or HMI F575 lamp head
The front focusing device is fitted with a bolt at the bottom hole of the holding plate. You can fix the Pulso G or the
-
HMI F575 onto this device. As shown on the image the lamp head must be positioned diagonally (image 6).
If using the lamp head Unilite, the bolt must be screwed tightly at the top hole of the holding plate.
-
Run the lamp head cable through the Velcro
-
6. Mounting of the Ringflash P on Para FB umbrella
- Unscrew the side screw and remove the adapter from the Ringflash P. Afterwards slide the Ringflash P along the
focusing bar of the Para FB umbrella until it is behind the adapter plate of the focusing bar (image 10). Rescrew
the adapter to the Ringflash P.
- Pass the fixing screw through the outer hole of the adapter of the Ringflash P and screw the Ringflash P to the
adapter plate of the Para FB umbrella (image 11). By slightly loosening the side screw on the Ringflash P, it is
possible to pivot the lamp vertically.
- To pivot the Ringflash P horizontally, the lamp must be tilted to 90° and fixed with the fixing screw in the middle
hole of the Ringflash P adapter. For reasons of space, the lamp holder bolt, which is also fixed on the adapter
plate of the Para FB (image 12), must be previously dismounted.
Dismounting the umbrella reflector
1. Folding the umbrella reflector
Remove the bar handle.
-
Put the umbrella in a vertical position.
-
Fold the umbrella with the crank gear (images 7,8 and 9).
-
Attention: Ensure that the umbrella fabric does not lie over any joints, otherwise it could become damaged.
Lash the umbrella together with the Velcro
-
Place the umbrella in a horizontal position again and put the protective ribbon over the circular base holding the
-
supporting spokes.
Remove the umbrella from the stand and pack it into the container (the tilt head must not necessarily be
-
removed).
Warning: When using a diffuser, the lamp head of the umbrella must not be directed to the front towards the diffuser.
Before using a diffuser, remove the extension adapter for Para FF/FB.
Bron Elektronik AG
CH-4123 Allschwil
Schweiz (Switzerland)
®
strap, which holds together the umbrella reflector.
®
strap (image 8).
MI 005.04
®
opening in the umbrella cove behind the umbrella.