Werbung
Verfügbare Sprachen
Verfügbare Sprachen
LCD Digital Picture Frame
GB
Please read these operating instructions carefully
prior to operation and keep them for later reference.
1 Applications
On its TFT LCD screen, the DPF-170 will allow to dis-
play pictures and change them automatically after a
time to be adjusted (slide show). For this purpose, the
pictures must be available in JPEG format on a mem-
ory card (SD, SDHC, MMC or MS).
2 Safety Notes
The units (picture frame, power supply unit and remote
control) correspond to all required directives of the EU
and are therefore marked with
.
WARNING The power supply unit uses dangerous
mains voltage. Leave servicing to skilled
personnel only. Inexpert handling or
modification of the unit may result in
electric shock.
The units are suitable for indoor use only. Protect
G
them against dripping water and splash water, high
air humidity and heat (admissible ambient tempera-
ture range 0 – 40 °C).
Do not operate the picture frame and immediately
G
disconnect the power supply unit from the socket
1. if the picture frame or the power supply unit is vis-
ibly damaged,
2. if a defect might have occurred after the unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the units must be repaired by skilled per-
sonnel.
For cleaning only use a dry, soft cloth; never use
G
water or chemicals.
No guarantee claims for the units and no liability for
G
any resulting personal damage or material damage
will be accepted if the units are used for other pur-
poses than originally intended, if they are not cor-
rectly operated, or if they are not repaired in an
expert way.
If the units are to be put out of operation defin-
itively, take them to a local recycling plant for
a disposal which will not be harmful to the
environment.
1
2
3
MODE
DC 5V
SD /MMC/MS
6
7
Copyright
®
®
PF-170
3 Setting the Picture Frame into Operation
1) The DPF-170 is supplied with two slip-on face-
plates (one in silver, one in black). Replace the
faceplate, if required.
2) Screw on the bracket (8) for the picture frame via
the locking screw (1) on the rear side and position
it so that the picture frame will be set up in a slightly
inclined way.
3) Connect the plug of the power supply unit to the
jack DC 5 V (6) and connect the power supply unit
to a socket (100 – 240 V~/50 – 60 Hz).
4) Switch on the display with the button
remote control or with the button
ture frame. If no memory card is inserted, a test pat-
tern will appear.
5) Insert a memory card with digital pictures in JPEG
format into the slot SD/MMC/MS (7) in such a way
that the contacts of the card will point downwards
and towards the slot. The card will be loaded imme-
diately and a picture will be displayed.
3.1 Remote control
When actuating a button on the remote control, always
direct the remote control towards the picture frame.
There must be no obstacles between the remote con-
trol and the red sensor window at the front of the pic-
ture frame.
If the range of the remote control decreases,
replace the battery. For this purpose, push the lock on
the rear side to the right while removing the battery
support downwards at the same time.
Insert the battery (3 V lithium button cell of type
CR 2032) into the support with its positive pole facing
upwards and slide the support back into the remote
control until it engages.
If the remote control is not used for a longer period,
remove the battery to prevent damage to the remote
control due to battery leakage.
Used batteries must not be placed in the
household waste; always take them to a spe-
cial waste disposal, e. g. collection container
at your retailer.
4
5
8
by MONACOR INTERNATIONAL GmbH & Co. KG, Bremen, Germany. All rights reserved.
©
Order No. 03.0740
(9) on the
(5) on the pic-
1.
2.
9
3
2
MODE
4
5
10
TIME
3.2 Operation
When a button is actuated, a toolbar will shortly be
inserted at the top of the display indicating the button
pressed or the setting selected.
1) To rotate the picture if the picture in the frame is
upside down or on its side, press the button
(repeatedly).
2) To adjust the suitable picture format, press the but-
ton MODE [2] (repeatedly).
3) To adjust the interval between pictures, press the
button TIME [10] (repeatedly):
5/15/30/60 seconds
5/15/30/45 minutes
1 hour
= no automatic change
The time will also be selected when the button
(3) on the picture frame is kept pressed for a longer
time.
4) To discontinue/continue the automatic change,
press the button
(5).
5) To return to the previous picture, press the button
(4). To go to the next picture, press the button
6) To switch off, press the button
trol or the button
on the picture frame until the
DPF-170 is switched off.
If the picture frame is not used for longer period,
disconnect the power supply unit from the mains,
as it will have a low power consumption, even when
the picture frame is switched off.
4 Specifications
Screen: . . . . . . . . . . . . . 17.5 cm (7") LCD display
Resolution: . . . . . . . . . . 480 × 234 pixels
Image file format
supported: . . . . . . . . . . . JPEG, 16 megapixels max.
Memory cards
supported: . . . . . . . . . . . SD
up to 2 GB
SDHC up to 8 GB
MMC up to 2 GB
MS
up to 8 GB
Power supply: . . . . . . . . 5 V / 1 A max. via power
supply unit provided and
connected to
100 – 240 V~/50 – 60 Hz,
10 VA max.
Dimensions, weight: . . . 230 × 164 × 33 mm, 460 g
Subject to technical modification.
1 Locking screw for the bracket (8)
2 Button MODE to switch over the picture format
3 Button
to rotate the picture by 90°
4 Buttons
and
to go to the previous/next pic-
ture
5 Button
to discontinue/continue the automatic
change of pictures
6 Jack DC 9 V to connect the power supply unit
7 Insertion slot for a memory card
8 Bracket for the frame
9 On/off button
10 Button TIME to adjust the interval between pictures:
5/15/30/60 seconds
5/15/30/45 minutes
1 hour
= no automatic change
A-1019.99.01.07.2009
[3]
.
on the remote con-
Werbung
