Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating instructions
LED driver
Item no. 1217847
Intended use
The LED driver is specially designed as a power supply for LED lighting. The product is protected
against short-circuiting, overload and overheating.
The LED driver supplies constant output current of 350 mA.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you
use the product for purposes other than those described above, the product may be damaged. In
addition, improper use can cause hazards such as short circuiting, fire, electric shock etc. Read
the instructions carefully and keep them. Make this product available to third parties only together
with its operating instructions.
This product complies with the statutory national and European requirements. All company names
and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• LED driver
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on proper
handling in this manual, we assume no liability for any resulting personal injury or
damage to property. Such cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Only install and use the product indoors in dry and closed rooms. The product must
not get damp or wet, as such conditions constitute a risk of electric shock!
• Make sure that the total power of the connected LED lighting does not exceed the
product's max. output power (see Technical Data).
• Operate the product only under the specified temperature conditions (see Technical
Data). Do not exceed the maximum ambient temperature (ta).
• Never immerse the product into water or other liquids.
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
Installation and connection
Have the product installed by a qualified expert (e.g. electrician) who is familiar with
all applicable regulations!
When handling mains voltage improperly, you will not only endanger yourself but also
others!
If you do not have the relevant expert knowledge, do not install the product yourself,
but have it done by an expert.
• The product must be completely free of voltage for installation.
• Turn off the corresponding circuit breaker and/or automatic fuse to remove all voltage from the
power circuit. Secure them against unauthorized restart, e.g. by installing a warning sign. Also
switch off the relevant circuit breaker in order to disconnect all poles of the mains cable from the
mains supply.
• Check the power circuit for any remaining voltage using an appropriate measuring device.
• Make sure there is a clearance of at least 50 mm between the LED driver and other objects/surfaces
when installing the product.
• First, connect your LED lighting to the connection cable of the secondary side (SEC), heeding
correct polarity. The length of the cable between the LED lighting and the LED driver may not
exceed 2 m.
• Connect the power supply line to the corresponding connection cable on the primary side of
the LED driver (PRI).
AC-N (blue)
200-240 V/AC
AC-L (brown)
• Install the product using the two mounting openings to an even, stable surface (i.e. wall, ceiling).
• Make sure not to damage any cables, wiring or pipes that may run beneath the installation
surface when installing the product.
• Finally, make sure the LED driver is correctly connected; do not turn on the power supply until
you have verified that the product is installed correctly.
• The LED driver is operational as soon as voltage is applied to the primary side.
Maintenance and cleaning
• This product does not require maintenance. There are no components located inside the product
you need to maintain. Never open/dismantle the product. Have maintenance and repairs done
by qualified experts or repair shops only.
• Disconnect the product from the power supply before cleaning. To clean the product, a dry,
soft and clean cloth is sufficient. You can use a long-haired, soft and clean brush and a vacuum
cleaner to remove dust.
• Never use any aggressive cleaning agents or chemical solutions as they may cause damage to
the housing or the product to malfunction.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household
waste.
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.
Technical data
Input ...............................................................200 – 240 V/AC, 50 Hz
Output voltage ..............................................0 – 34.3 V/DC
Output current ..............................................350 mA
Rated power..................................................12 W
No-load voltage ............................................max. 38 V/DC
Input cable ....................................................H03VVH2-F 2 x 0.75 mm
Output cable..................................................H03VVH2-F 2 x 0.75 mm
Protection class ...........................................II
Housing temperature...................................max. +80 ºC (tc)
Operating conditions ...................................-20 to +45 ºC (ta), 10 – 85 % RH
Storage conditions.......................................-20 to +50 ºC, 10 – 95 % RH
Dimensions (W x H x D)...............................132 x 52 x 13 mm
Weight ............................................................approx. 81 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE.
132 mm
+ (red)
- (black)
2
2
LED lighting
V3_0914_02-KV
Werbung
