Werbung
Quicklinks
CoreLine
Waterproof
WT120C G2 MDU
WT120C G2 LED19S/840 PSU MDU L600
WT120C G2 LED27S/840 PSU MDU L1200
WT120C G2 LED27S/840 PSU MDU TW3 L1200
WT120C G2 LED40S/840 PSU MDU L1200
WT120C G2 LED40S/840 PSU MDU TW3 L1200
WT120C G2 LED34S/840 PSU MDU L1500
WT120C G2 LED34S/840 PSU MDU TW3 L1500
WT120C G2 LED60S/840 PSU MDU L1500
WT120C G2 LED60S/840 PSU MDU TW3 L1500
WT120C G2 LED80S/840 PSU MDU L1500
Type
WT120C G2 LED19S L600
WT120C G2 LED27S L1200
WT120C G2 LED40S L1200
WT120C G2 LED34S L1500
WT120C G2 LED60S L1500
WT120C G2 LED80S L1500
444316022532 - 01
© 08 / 2020 Signify Holding All rights reserved
220 V
50 Hz
240 V
60 Hz
System light
output (Lm)
1900
2700
2700
4000
4000
3400
3400
6000
6000
8000
E max
E min
B
A
B
665
1215
76
1515
Max
.
35 °C
Min.
50K hrs
-20°C
kg
0,9
1,4
1,5
1,4
1,5
1,7
1,8
1,7
1,8
1,7
Dimension (mm)
C
D
E
E
min
308
538
1062
80
38
838
1362
1/10
LIFE
L75
IP65
Nr. of
F
clips
max
512
6
10
85
12
Printed in Hungary
Data subject to change without notice
Keep for future reference: www.philips.com/lighting
24
27
T
20
GLOW
IK08
WIRE
850 °C
D
C
Werbung
Inhaltszusammenfassung für Philips WT120C G2 LED19S/840 PSU MDU L600
- Seite 1 60 Hz 50K hrs 850 °C -20°C System light output (Lm) 1900 WT120C G2 LED19S/840 PSU MDU L600 2700 WT120C G2 LED27S/840 PSU MDU L1200 2700 WT120C G2 LED27S/840 PSU MDU TW3 L1200 4000 WT120C G2 LED40S/840 PSU MDU L1200...
- Seite 2 OPTIONAL ANTI-VANDAL MOUNTING PSU versions 0,75-2,5mm² 8-12mm TW3 versions 0,75-2,5mm² 8-12mm Through wiring 2/10...
- Seite 3 Mid - or side - entry (optional) Switch off the power supply Knock out for cable entry before installation 0,75-2,5mm² 8-12mm Replacement of Silicone Plug (optional) N ew S ilicon e P lu g Ø 12-14 m m 3/10...
- Seite 4 Remove protection foil after installation and before usage! TW3 versions Start of line End of line 4/10...
-
Seite 5: Dip Switch Settings
Microwave Motion Sensor The sensor is designed to connect one load only. Connecting more than one load may damage the sensor. DIP Switch settings: Daylight sensor (default disabled) Detection area Hold time (default 5 min.) The sensor can be set to only allow the (default 100%) Refers to the time period the Detection area can be reduced... - Seite 6 The sensor is designed to reliably detect walking people. Microwave sensors can detect movement behind walls (brick, dry wood, acrylic board, glass, etc.). The detection behind walls can be reduced by choosing a lower sensitivity setting (use Dip switches 3 and 4 to choose a sensitivity lower than 100%). Other undesired detections can be caused by: Strong electromagnetic fields;...
- Seite 7 Driver replacement 1,2Nm New driver LED19S LED27S LED34S LED40S LED60S LED80S Driver type Ipeak [A] 3,58 3,58 5,16 5,16 5,56 Tref [μs] Max. Nr of products Drivers / MCB 16A type B [max.] Drivers / MCB 10A type B [max.] Drivers / MCB 16A type C [max.] Drivers / MCB 10A type C [max.] * Do not stare into LED light beam...
- Seite 8 GB - Disconnect before servicing DK - Frakobl, før service IT - Toglieretensioneprima di fare manutencione FR - Mettrehors tension avantintervention NO - Koble fra før service ES - Desconectarantes de manipular DE - Offnennurspannungsfrei FI - Irrota pistoke ennen huoltoa SE - Brytströmmenförelampbyte NL - Stroom afsluiten voor onderhoud CZ - Před servisem se odpojte...
- Seite 9 Opbevaring, installation, brug, betjening og vedligeholdelse af produkterne ma kun udfores ifolge instruktionerne i denne vejledning og/eller eventuelle ovrige instruktioner fra Philips Lighting for at garantere sikker brug af produktet i hele dets levetid. Hvis disse instruktioner ikke folges, bortfalder produktgarantien.
- Seite 10 Depozitarea, instalarea, utilizarea, operarea și întreșinerea produselor trebuie să fie efectuate exact în conformitate cu instrucșiunile din acest manual și/sau cu alte instrucșiuni care pot fi furnizate de noi pentru a garanta utilizarea în siguranșă a produsului, pe întreaga durată de viașă a acestuia. Nerespectarea acestor instrucșiuni vă...
- Seite 11 © 2020 Signify Holding All rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.