Inhaltsverzeichnis
Werbung
TPCE Specification
7.4 TPCE Spezifikation
40 - 240 MHz Data Acquisition Modules
Module Type
Number of Input Channels SE Module
Number of Input Channels DIF Module
Max. Sample Rate
(all channels are sampled simultaneously)
Amplitude Resolution
Memory (per Module)
Input Amplifier
Measurement Ranges
Offset
Input Impedance
Coupling
Bandwidth at Range ≥ 1 V
Bandwidth at Range < 1 V
Slew Rate (10 – 90 %) @ Range ≥ 1 V
Slew Rate (10 – 90 %) @ Range < 1 V
Settling Time to 1%
Low Pass Filter (RC-Filter)
Antialiasing-Filter (optional)
Common Mode Range
Common Mode Rejection
Range Error (±)
Offset Error (±)
Offset Drift (±)
Input Noise:
@ max. Sample Rate
@ 5 MHz Sample Rate
@ 1 MHz Sample Rate
@ 100 kHz Sample Rate
@ 10 kHz Sample Rate
Signal to Noise Ratio SNR:
@ max. Sample Rate
@ 10 MHz Sample Rate
@ 5 MHz Sample Rate
@ 1 MHz Sample Rate
@ 100 kHz Sample Rate
@ 10 kHz Sample Rate
Channel Isolation (Crosstalk) @ 10 kHz
Ranges < 1V
Special : Autocalibration
Trigger
Number of Trigger Channels
Advanced Trigger (Option)
External Trigger input
Trigger Delay
Miscellaneous
Digital Inputs (Marker)
Ext. Control Inputs (TTL))
Status Outputs (TTL)
ICP® Sensor Supply (Option)
© 2016 Elsys AG
Specifications subject to change without notice.
Elsys AG
TPCE-24016-4
TPCE-12016-4
4 single ended or 2 differential
software switchable
4 single ended or 4 differential
software switchable
240 MHz
120 MHz
16 Bit up to 60 MHz
16 Bit up to 60 MHz
14 Bit up to 240 MHz
14 Bit up to 120 MHz
Standard: 4 x 32 MWords (= 256 MByte)
Optional: 4 x 128 MWords (= 1 GByte)
±50 mV – ±50 V rsp. 0.1 V – 100 V (100 V limited to 70 V) in 1, 2, 5 Steps
0 – 100 % in steps of 0.1% (Resolution 0.01 %)
1 MΩ (± 0.2 %) or 50 Ω (± 0.5 %)
// 26 pF (± 5 %)
AC / DC software switchable (AC: -3 dB at < 5 Hz), Inputs invertible
120 MHz
60 MHz
80 MHz
50 MHz
4 ns
6 ns
< 200 ns
< 200 ns
2 Steps ( 1 MHz and 100 kHz) software switchable
200 Hz – 5 MHz, min. 4. order Butterworth, software setable
Differential-Mode: ±8 V or +/-80 V at ranges. > 5 V
> 74 dB (DC – 1 kHz); > 60 dB ( – 100 kHz); > 40 dB ( – 5 MHz)
max. 0.1 % typ. 0.07 %
(after autocalibration)
max. 0.1 % typ. 0.07 %
(after autocalibration)
max. (0.0100 % + 0.1 mV) per °C, typ. (0.0050 % + 0.03 mV) per °C
(will be compensated by autocalibration)
< 0.250 mVrms
< 0.200 mVrms
< 0.120 mVrms
< 0.120 mVrms
< 0.070 mVrms
< 0.070 mVrms
< 0.040 mVrms
< 0.040 mVrms
< 0.025 mVrms
< 0.025 mVrms
59 dB
62 dB
62 dB
68 dB
66 dB
70 dB
69 dB
74 dB
79 dB
82 dB
89 dB
90 dB
Auto adjustment of gain and offset in all measurement ranges. (Initiated by software)
4 coupled to analog inputs, pos./neg.Edge, with or without hysteresis,
On all analog inputs: Slew Rate, Pulse Width, Pulse Pause or Period (too short or too long
= Missing Event), State (above / below), AND link, Product (trigger signal is calculated from
1 per System (TTL), pos. or neg. Edge
-100 % (Pretrigger) to +200 % (Posttrigger) in 1 % steps
8 (2 per analog channel) (TTL)
Optocoupler Connection Box (5 to 48 V) as additional option
Trigger, Arm/Disarm, Ext. Sampling (fmax = 10 MHz), external command to start recording
Trigger Output, Armed (=True during recording)
4mA Integrated Current Power for piezo sensors
www.elsys-instruments.com
TPCE-8016-4
4 single ended or 2 differential
software switchable
4 single ended or 4 differential
software switchable
80 MHz
16 Bit up to 20 MHz
14 Bit up to 80 MHz
1 MΩ (± 0.2 %) // 35 pF (± 5 %)
30 MHz
8 MHz
6 ns
13 ns
9 ns
50 ns
< 200ns
max. 0.1 % typ. 0.03 %
(after autocalibration)
max. 0.1 % typ. 0.02 %
(after autocalibration)
< 0.200 mVrms
< 0.120 mVrms
< 0.070 mVrms
< 0.040 mVrms
< 0.020 mVrms
67 dB
70 dB
72 dB
76 dB
84 dB
92 dB
> 80 dB
> 60 dB
Window IN, Window OUT
2 channels)
Benutzerhandbuch
TPCE-4016-4
40 MHz
16 Bit up to 10 MHz
14 Bit up to 40 MHz
18 MHz
7 MHz
25 ns
60 ns
< 200 ns
< 0.180 mVrms
< 0.110 mVrms
*2
< 0.060 mVrms
< 0.040 mVrms
< 0.015 mVrms
70 dB
70 dB
72 dB
*3
76 dB
84 dB
92 dB
1 / 3
19
Werbung
Inhaltsverzeichnis
