Product Familiarisation; Specification - Triton TWX7 Sicherheits- Und Bedienungsanleitung

Introduction
Thank you for purchasing this Triton product. This manual contains information necessary for
safe and effective operation of this product. This product has unique features and, even if you
are familiar with similar products, it is necessary to read this manual carefully to ensure you
fully understand the instructions. Ensure all users of the product read and fully understand
this manual.
Description of Symbols
The rating plate on your tool may show symbols. These represent important information about
the product or instructions on its use.
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction manual
Caution!
Risk of fire!
Toxic fumes or gases!
Environmental Protection Waste electrical products should not be disposed of
with household waste. Please recycle where facilities exist. Check with your local
authority or retailer for recycling advice.

Specification

Dimensions (L x W x H):
Outlet adaptor diameter:
Weight:
As part of our ongoing product development, specifications of
Triton products may alter without notice.
Carefully read and understand this manual and any label attached to the tool before use.
Keep these instructions with the product for future reference. Ensure all persons who use this
product are fully acquainted with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk factors. Use with
caution. If you are at all unsure of the correct and safe manner in which to use this tool, do
EN
not attempt to use it.
4
Original Instructions
660 x 410 x 265mm
Inner: 36mm
Outer:
40mm
0.5kg
Specific Safety
Downdraft Table Safety
WARNING: Downdraft table is for the collection of wood dust particles ONLY. DO NOT use
this product to collect metal swarf metal particles.
WARNING: Ensure that any extraction system is switched OFF and disconnected from the
downdraft table before cleaning or carrying out any maintenance.
WARNING: This product is for dry use only; do not attempt to pick-up fluids, or use in
high-humidity locations.
WARNING: Keep away from combustible substances. The large amounts of dust and
wood chippings stored within the dust extractor create a fire hazard. Remove debris from the
collector frequently.
WARNING: Use this product only for the purposes for which it is intended. Other
applications may be dangerous, and lead to serious injury and/or property damage.
WARNING: ALWAYS wear appropriate personal protective equipment, including eye and
respiratory protection when working with this product.

Product Familiarisation

1. Rubber Lip
2. Dust Outlet
3. Support Rods
4. Fixing Dogs
5. Dust Outlet Adaptor
6. Support Rod Sleeves
Intended Use
Dust collection attachment for use with the TWX7 Workcentre and clamping module to
create a woodworking downdraft table with the use of a compatible dust extraction system.
Before Use
WARNING: ALWAYS wear appropriate personal protective equipment, including eye and
respiratory protection when working with this tool.
Assembling the dust collection attachment
1. Insert the four Support Rods (3) into the four Support Rod Sleeves (6) on each corner
of the dust collection attachment (Fig. I)
2. Insert the Dust Outlet Adaptor (5) into the Dust Outlet (2) (Fig. II)
Attaching the dust collection attachment to the
Workcentre clamping module
1. Remove the clamping module from the Workcentre if attached
2. Flip the clamping module to access the underside of the module
3. Loosen but do not remove the screw in the Fixing Dogs (4) (Fig. III)
4. Insert the four Fixing Dogs into the holes in the clamping module (Fig. IV)
5. Tighten the screw in the Fixing Dogs to secure the Fixing Dogs to the clamping module
6. Carefully stretch the Rubber Lip (1) of the dust collection attachment over
the Fixing Dogs (Fig. V)
7. Insert the clamping module into the Workcentre and lock in place (Fig. VI)
8. Attach a compatible dust extraction system to the Dust Outlet Adaptor (5) (Fig. VII)
Carrying out a test run
• Before carrying out sanding operations always check the fitting and condition of the
downdraft table
• Switch the dust extraction system ON and inspect the downdraft table for air leaks