Werbung
Verfügbare Sprachen
Verfügbare Sprachen
UNIVERSAL REMOTE CONTROL
OPERATING INSTRUCTIONS
This 6 in 1 universal remote control replaces up to six remote controls
and is compatible with almost all major brand devices.
It can be used to operate the following types of device
TV: television set
VCR: video recorder
DVD: DVD player
CABLE: cable receiver
SAT: Satellite receiver
AUDIO: audio devices
Please read these instructions carefully before using the remote control
for the first time.
We recommend to start with the automatic channel scan.
Note:
a) When replacing the batteries, do not press any buttons. Otherwise
the programmed settings and codes may change.
b) Reset all commands before starting the programming. To reset,
press (SET)+(TV) and enter (9) (9) (0). The reset is successfully
completed when the LED flashes three times.
Your universal remote control is capable of performing the most
common functions of device remote controls.
- Please note that in some cases the universal remote control cannot
perform all special functions of a device remote control.
- At the end of this guide you will find device codes for many types of
equipment. Please note, however, that there may be devices which
cannot be operated with this universal remote control.
Intended Use
The universal remote control is used to operate consumer electronics
devices and is designed for indoor use in private homes. It is intended
exclusively for these purposes and must not be used for any other
purpose. It must only be used as described in these operating
instructions. Any other use is considered incorrect and may result in
damage to the remote control or the equipment.
Inserting batteries
The battery compartment is located on the back of the universal remote
control.
Insert two size AA batteries (LR6, 1.5 V) in the battery compartment and
pay attention to polarity (+/- poles). Press the ON/OFF button. The
universal remote control works properly when the red LED light comes
on.
Caution!
If you replace the batteries, all codes stored by the universal remote
control will be deleted. For this reason, write down the codes used for
programming before replacing the batteries.
Remove the batteries from the universal remote control if you do not
use it for a longer period.
5
TV
VCR
14
DVD CAB AUD
13
1
2 3
4
5 6
12
6 7 9
7
0
OK
11
10
Overview:
1:
Red LED flashes during operation and is constantly lit during
programming
2:
Switching the device on and off
3:
Setting the device to mute
4:
Teletext buttons. Use these buttons like the teletext buttons on
your TV remote control
a:
Switching on teletext
b:
Switching off teletext
c:
Teletext page on hold (within a sequence of continuous pages)
5:
Volume up (+), volume down (-)
6:
Changing TV channels up (CH+) or down (CH-)
7:
INPUT TV/VCR. Use this button like the AV button on your TV
set. Press the button several times to select the input source (
"AV1", "AV2", etc.)
8:
For calling up the menu of the respective device
9: SET: Setup
10:
Play buttons. Use these buttons to control the playback functions
of the selected device (e. g. VCR, DVD player, DVD recorder)
SKIP backwards
Press to start playback
SKIP forward
Press to start recording
Press to stop playback
II
Press to pause playback
11:
OK: Press to confirm an entry
12:
Number buttons. Press to select a TV program or to make a
numeric entry.
13:
Coloured buttons. Use these buttons for teletext. Use the red
button to perform the function that is displayed within a red box,
etc.
14.
Device buttons. The device codes are assigned to these buttons.
TV:
Applies only to TV set.
VCR, SAT, DVD, CAB, AUD: For other devices
SAT
a
b
c
+
VOL
VOL
-
+
CH
CH
INPUT
-
TV-VCR
MENU
SET
6
1
2
3
4abc
4abc
5
6
7
8
9
Werbung
