Renkforce 1675013 Gebrauchsanweisung Seite 2

Operating Instructions
Universal Smart-Stand for Notebooks
Item No. 1675013
Intended Use
This stand is ultra-thin and can raise your laptop to improve ergonomics. It
has 6 adjustable positions and stays attached without adding much size.
The space it creates underneath your computer can also help keep it cool.
For safety and approval purposes, you must not rebuild and/or modify this
product. If you use the product for purposes other than those described
above, the product may be damaged. Read the instructions carefully and
store them in a safe place. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements.
All company names and product names are trademarks of their respective
owners. All rights reserved.
Delivery Content
• Stand
• 2 x spare adhesive strips
Up-to-date Operating Instructions
Download the latest operating instructions at www.
conrad.com/downloads or scan the QR code shown.
Follow the instructions on the website.
Operating Elements
1
2
3
4
5
Installation
a) Preparation
• Make sure there are no protruding or removable
components that may interfere with installation.
• Wipe the base of your laptop clean. See section "Care and
Cleaning".
• Make sure the surface is completely dry before applying
the adhesive strips. The strips will not adhere to soft case
materials e.g. Silicone, TPU/TPE.
b) Drawing Guide Lines
Place notebook on soft surface and use a pencil softer
than HB hardness to protect the bottom case from getting
scratched. Make sure the stand does not cover the cooling
slots of your notebook.
• Draw three guide lines as shown.
• The top guideline should be drawn above the
rubber feet on the base.
• The vertical lines should be drawn to align the
stand in the middle.
c) Attach Stand to Laptop
• Carefully remove the adhesive strips.
• Line the stand up along the marks, upper
stand (1) edge along the top line.
• Carefully press down to help with adhesion.
Care and Cleaning
• Turn your computer off, disconnect the computer from its power source
and allow to cool to room temperature.
• Do not use any aggressive cleaning agents or other chemical solutions as
they can cause damage to the product.
• Clean the product with a dry, fibre-free cloth.
Disposal
At the end of its service life, dispose of the product in
accordance with applicable regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the
protection of the environment.
Technical Data
Material ............................................................Zinc alloy & stainless steel
Compatibility .................................................... Max. 18" laptop screen size
Adhesive tape ..................................................No residue adhesive
Stand height ....................................................6 x positions (7 -12 cm)
Dimensions (W x H x D) .................................. 141 x 140 x 1.7 mm
Weight .............................................................136 g
• 4 x rubber feet
• Operating instructions
1 Upper stand
2 Lock/release (upper)
3 Lock/release (lower)
4 Lower stand (height adjust)
5 Frame
(intact bottom case)
(retracted)
Explanation of Symbol
The symbol with the exclamation mark in the triangle is used to
indicate important information in these operating instructions.
Always read this information carefully.
Safety Instructions
Read the operating instructions carefully and especially
observe the safety information. If you do not follow the
safety instructions and information on proper handling
in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will
invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children
and pets.
• Do not leave packaging material lying around carelessly.
This may become dangerous playing material for children.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take
it out of operation and protect it from any accidental use.
Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient
conditions or
- has been subjected to any serious transport-related
stresses.
• Please handle the product carefully. Jolts, impacts or a fall
even from a low height can damage the product.
• Consult an expert when in doubt about the installation.
• Modifications and repairs must only be completed by a
technician or an authorised repair centre.
• If you have questions which remain unanswered by these
operating instructions, contact our technical support service
or other technical personnel.
d) Attach Rubber Feet
Make sure the long rubber feet are attached to the front edge
as shown.
• Stick the rubber feet above the feet on your
laptop. Align the longer feet with the front
edge as shown.
• Press the feet down to ensure good
adhesion.
e) Stand
The stand may leave marks or scratches on sensitive
surfaces. Make sure the stand is fully locked out before placing
the weight of your laptop onto it.
• Using the center hole, slide the upper stand
(1) all the way out until you hear a "click".
• You can further adjust the stand height
(up to 6 levels) by pulling the lower stand,
height adjust (4).
f) Retracting the Stand
• While keeping your fingers clear, press lock/release buttons (2) and (3).
• Push the plates down until they are flush with the laptop case.
g) Removing Stand from Laptop
To protect the case material, do not use a hard object. Use a
deactivated credit card or similar. Do not use force to peel the
stand away from the laptop.
• Carefully insert a deactivated credit card (or
similar) into the space between the frame (5)
and laptop case.
• Gently slice into the adhesive tape, following
along the edge until the stand is completely
removed from the laptop.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com). All rights including translation
reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior
written approval by the editor. Reprinting, also in part, is prohibited. This
publication represents the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE.
*1675013_v1_0618_fl10_02_m_de_gb_(2)