Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN Installation and Operating Instructions
LED Floodlight YORK
Art. No. 501026, 501027, 501028, 501029, 501030, 501031, 501032
These operating instructions refer exclusively to the above products.
They contain important informations for the start-up and handling of the lamp.
Therefore, pay attention to these operating instructions, even if you pass this product on to
third parties
1. Introduction
Dear customer, thank you for deciding to purchase our product.
You have acquired a product from Vollmer, which has been built according to the current state of
technology.
The light fulfils the requirements of effective European and national guidelines
To maintain the condition of the product and to ensure safe operation, you - as the user - must observe the
instructions of this operation manual!
2. Safety Instructions
•
The guarantee becomes invalid if damage occurs due to the failure of following these operating instructions!
•
We do not accept liability for any consequential damage!
•
Commissioning is strictly prohibited if there are any damages on the lamp.
•
Do not allow children to play unsupervised near lamps or other electrical devices.
•
The lamp becomes hot during operation. The outside of the lamp housing also becomes hot. Do not
touch the light with your bare hands during operation. Do not allow the light to come into contact with extreme heat or naked
flames.
It´s not allowed to modify the product. Alterations to the light invalidate the guarantee.
•
It´s not allowed to remove the type plate
3. Proper Use
This lamp is designed for outdoor use.
This product is only intended for lighting purposes and may:
•
only be operated with a voltage of 230V ~50Hz
•
only be connected according to protection class I (one)
•
only be operated when mounted to a sturdy, level and non-tilting surface
•
only be operated on normal or non-flammable surfaces
•
not be subjected to strong mechanical loads or heavy soiling.
4. Before Installation/Commissioning
•
It´s not allowed to operate the lamp inside the packaging.
•
Remove the lamp from the packaging carefully.
•
Make sure that the lamp has not been damaged during transport before taking the lamp into operation.
It´s not allowed to operate the lamp if there are any damages to electrical parts. Repairs may only be carried out by a qualified
electrician.
•
Keep packaging materials away from children and pets. Danger of suffocation!
5. Installation/Commissioning
•
This product may only be installed by a qualified electrician.
•
The connection lines in the building must be disconnected before installation and secured against being switched back on. For
this, trip the corresponding fuse switch in the building installation.
•
Use a VDE compatible Voltage detector to proof if the Line is dead.
•
For your personal security let the RCD online even if the Miniature Circuit Breaker is off, since the RCD normally serves as
personal protection for more than one circuit.
•
Make sure that the surface is suitable for permanently and reliably taking the weight of the luminaire.
•
Hold the lamp housing in the required mounting position and mark the drill holes. Use suitable screws to fix the light. Make sure
that no cables are damaged.
•
Now connect the connection cables of the house installation to the luminaire. Please use an IPX5 cable connector for this. First
connect the green-yellow protective conductor (PE) and then the other two lines. Usually the brown / black wire is the phase
conductor (L), connect this to the terminal marked with an "L". The blue wire is the neutral wire (N), this must be connected to
the terminal marked with "N". Tighten the screws of the terminal firmly so that the wires cannot slip out.
•
Do not bend the cables; make sure that the cables and plugs are not subject to tension or torsionalforces. Protect all cables and
insulation against possible damages.
•
Check proper connection once again.
•
Fill the light with the materials you have chosen (pay attention to the safety advice!)
•
Switch the building installation's fuse/switch back on.
6. Malfunction
Floodlight does not switch on
•
Lamp switched on at the wall switch?
•
Check the connected cables
•
Is the motion sensor blocked?
•
Is the motion sensor dirty?
7. Changing Illuminants
The LED module is permanently installed and cannot be replaced.
8. Technical Data
Itemn.
Connection
Execution
501026
230 V~AC 50Hz
10W, 1000lm, 3000K
501027
230 V~AC 50Hz
20W, 2000lm, 3000K
501028
230 V~AC 50Hz
30W, 3000lm, 3000K
501029
230 V~AC 50Hz
10W, 1000lm, 3000K
with ground spike
Illuminante
Protection class
Protection class
LED - non modifiable
IP65
1
LED - non modifiable
IP65
1
LED - non modifiable
IP65
1
LED - non modifiable
IP44
1
1 von 2 |
31.08.2020
Werbung
