Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating instructions
LED transformer
Item no. 792398
Intended use
This compact LED transformer provides a constant output voltage of 12 V/DC. The product
is protected against short-circuiting, overload and overheating.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting, fire,
electric shock etc. Read the instructions carefully and keep them. Make this product
available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• LED transformer
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• For safety and approval purposes (CE), you must not rebuild and/or modify
this product.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• Only install and use the product indoors in dry and closed rooms. The
product must not get damp or wet, as such conditions constitute a risk
of electric shock!
• Make sure that the total power of the connected LED lighting does not
exceed the transformer's max. output power (see Technical Data).
• Operate the product only under the specified temperature conditions
(see Technical Data). Do not exceed the maximum ambient temperature
ta = 45 °C.
• Never immerse the product into water or other liquids.
• Consult an expert when in doubt about operation, safety or connection
of the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Installation and connection
Have the product installed by a qualified expert (e.g. electrician) who is
familiar with all applicable regulations!
When handling mains voltage improperly, you will not only endanger
yourself but also others!
If you do not have the relevant expert knowledge, do not install the product
yourself, but have it done by an expert.
• The product must be completely free of voltage for installation.
• Turn off the corresponding circuit breaker and/or automatic fuse to remove all voltage
from the power circuit. Secure them against unauthorized restart, e.g. by installing a
warning sign. Also switch off the relevant circuit breaker in order to disconnect all poles
of the mains cable from the mains supply.
• Check the power circuit for any remaining voltage using an appropriate measuring
device.
• Make sure there is a clearance of at least 50 mm between the transformer and other
objects/surfaces when installing the product.
• Loosen the four screws using a Phillips screwdriver and remove both covers from the
transformer housing.
• First, connect your LED lighting to the screw terminals on the secondary side (SEC;
12 V/DC), heeding correct polarity. The length of the cable between the LED lighting
and the LED transformer may not exceed 2 m.
• Alternatively, you can connect the LED lighting to the DC socket (12 V/DC, 0.5 A) using
the DC plug.
• Connect the power supply line to the corresponding screw terminals on the
primary side of the LED transformer (PRI; 200 – 240 V/AC). Make sure that all screw
connections are firmly tightened.
200-240 V/AC
N
L
• Put the covers on the transformer housing and fasten them using the screws.
• Install the product using the two mounting openings to an even, stable surface (i.e.
wall, ceiling).
• Make sure not to damage any cables, wiring or pipes that may run beneath the
installation surface when installing the product.
• Finally, make sure the LED transformer is correctly connected; do not turn on the
power supply until you have verified that the product is installed correctly.
• The LED transformer is operational as soon as voltage is applied to the primary side.
Maintenance and cleaning
• This product does not require maintenance. There are no components located
inside the product you need to maintain. Never open/dismantle the product. Have
maintenance and repairs done by qualified experts or repair shops only.
• Disconnect the product from the power supply before cleaning. To clean the product,
a dry, soft and clean cloth is sufficient. You can use a long-haired, soft and clean
brush and a vacuum cleaner to remove dust.
• Never use any aggressive cleaning agents or chemical solutions as they may cause
damage to the housing or the product to malfunction.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the
relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of
the environment.
Technical data
Input ...............................................................200 – 240 V/AC, 50 Hz
Output voltage ..............................................12 V/DC
Output current ..............................................0.5 A
Output power ................................................max. 6 W
Input terminals..............................................2 x 0.75mm
Output terminals ...........................................2 x 0.75mm
Protection class ...........................................II
Ambient temperature ..................................-20 to +45 ºC (ta)
Housing temperature...................................max. +80 ºC (tc)
Dimensions (W x H x D)...............................approx. 99 x 46 x 11 mm
Weight ............................................................approx. 42 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This
publication represent the technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE.
99 mm
LED
-
lighting
+
2
2
V3_0614_02-KV
Werbung
