Wieland wienet AP 3P ETH-A Montageanleitung Seite 2

Installation instruction (translation from original)
wienet AP 3P ETH-A
AP 3P ETH-A-A
WLAN Access Point with integrated 3-port switch
Personnel which installs, programs, operates or maintains this device must have read and
under-stood these instructions.
• Personnel must be familiar with all the warnings, notes and measures described in these
operating instructions.
• Protective measures and mechanisms must correspond to applicable regulations.
• Damaged products must neither be installed nor put into operation. In case of a defect,
please return the device to Wieland Electric.
• Only connect or disconnect the device when de-energized!
• The unit must not be opened!
• Do not insert foreign objects into the device!
• Keep the device away from water and fire!
1 License information
This device incorporates software from third-party providers under the license conditions of
GNU General Public License Version 2. You are permitted to modify or distribute this free
software under the conditions of the GNU General Public License. If required, you can re-
quest the source code of the software covered by the GNU General Public License. You can
find further information at:
https://dev.openwrt.org/browser/trunk/LICENSE
2 Function description
The wienet AP 3P ETH is a WLAN Access Point for devices that communicate wirelessly, and
it can also be configured as a repeater. Furthermore, it can be connected to devices that do
not have their own WLAN adapter. Because of its integrated 3-port-switch (port P1, P2, P3)
up to three devices can be connected. It is delivered configured with the factory settings and
ready for immediate use. The WAP can be configured for specific requirements via an inte-
gral web interface. Access is possible via LAN or WLAN.
3 Display and operating elements
LED Color Description
STATUS green LED off >10 s
P1, P2 LED flashes
P3 LED lights up
DATA yellow LED off >10 s
P1, P2,
P3 LED lights up
LED flickers
Button Description
RES Press RES <3 s
Press RES 5–30 s
The LEDs are integrated inside the RJ45 sockets of ports P1, P2 and P3. The three green
LEDs are connected in parallel and therefore turn on altogether. After switching on the
power supply, it takes approx. 10 seconds for the green LEDs to start flashing and about
25 seconds to shine steadily. A flashing LED indicates that the wienet AP 3P is not yet ready
for use (boot procedure or restart), whereas a continuously lit LED indicates that the device
is indeed ready for use (status OK). The three yellow LEDs indicate the state of the corre-
sponding port. After switching on the power supply, the yellow LEDs are flashing once. If a
LAN connection is set up, the yellow LEDs show an existing connection (yellow LED is on)
and activity (yellow LED is flashing).
4 Connection with Access Point
To ensure that a network connection can be established, your PC must be in the same net-
work.
4.1 Access via network cable
1. Connect the power supply.
2. Connect your PC to the wienet AP 3P (port "P1", "P2" or "P3") via Ethernet cable.
3. Enter the IP address of the network adapter manually on the PC:
IP address: 192.168.1.2 – 192.168.1.254
4.2 Access via LAN
1. Only for 83.040.0053.0: Connect the WLAN antenna ("ANT").
2. Connect the power supply.
3. Activate the WLAN connection on the PC and connect to the WLAN network.
4. Enter the IP address of the network adapter on the PC as described in 4.1, step 3:
SSID: wienet-AP-3P
Doc. # BA001150 – 11/2020 (Rev. C)
83.040.0052.0
83.040.0053.0
NOT E
WAR NING
or http://www.gnu.org/licenses/gpl-2.0
Function
No power supply available
The Access Point is starting up.
The Access Point is ready for use.
No power supply available or
RJ45 socket not connected
RJ45 socket connected without activity
RJ45 socket connected with activity
Function
Restart
Restart with factory settings
Network mask: 255.255.255.0
Password: wienet123
Wieland Electric GmbH
Brennerstraße 10 – 14
96052 Bamberg
Phone +49 951 9324-0
Fax +49 951 9324-198
info@wieland-electric.com
www.wieland-electric.com
5 Access to the Access Point web interface
The wienet AP 3P is configured via web interface using a web browser and can be accessed
as follows:
1. Open the following URL in the browser:
2. Enter the following password in the window that opens: root
The wienet AP 3P web interface then opens. If the window does not open, please check the
proxy settings for the browser you are using. Please do not use a proxy!
6 Individual Configuration
The wienet AP 3P is delivered configured with the factory settings and ready for immediate
use. The individual configuration is made via the web interface. We recommend performing
the initial configuration using the LAN interface of the device.
For your own security, change the password for accessing the web interface, the ESSID and
the WLAN password as well as the host name, country code and language, if required.
The IP address must be changed manually after delivery. You can also configure the wienet
AP 3P as a DHCP client (IP address retrieved from DHCP server) or as a DHCP server (IP ad-
dresses allocated to connected DHCP clients).
Save: Changes are adopted in the web interface.
Save & Apply: Changes are additionally transferred to the device.
If changes relevant to the connection are made (e.g. ESSID, IP address, password or WLAN
key), access to the web interface is only possible again after you connect and log on with the
new settings.
7 Load factory settings (reset)
Press the "RES" button at the top left above the port P3 to reset the factory settings, includ-
ing the IP address and access data.
Press the "RES" button for 5 – 30 seconds using a paper clip while the wienet AP 3P is ready
for use. Then wait until the green LED lights up (after approx. 35 s). The wienet AP 3P is now
ready for use again.
8 Technical data
Operating voltage connection
Connection type
Rated voltage
Voltage range
Approx. rated current
Approx. rated consumption
Reverse polarity protection
PE connection
Connector cross section
Torque
Wire strip length
WLAN
Wireless LAN standard
Frequency
Transmission power
Data rate
Safety
Antenna 83.040.0052.0
83.040.0053.0
LAN ports
Connection type
Medium
Screen / grounding
Environmental conditions
Usage area
Ambient operating temperature -5 ... +55 °C
Storage temperature
Relative humidity
Condensation
Mounting
Mounting method
Installation 83.040.0052.0
position
83.040.0053.0
Weight 83.040.0052.0
83.040.0053.0
Dimensions 83.040.0052.0
(W×H×D) 83.040.0053.0
Standards
Accessories for 83.040.0053.0 WLAN magnetic base antenna, article no. F0.000.0037.4
CE: Hereby, Wieland Electric GmbH declares that the wienet AP 3P ETH-A-x is in compliance
with the following European directives:
RED directive 2014/53/EU, RoHS directive 2011/65/EU.
The complete EU Declaration of Conformity is available with the respective part number
under e.g. https://eshop.wieland-electric.com/products/83.040.0052.0
"Downloads".
wienet AP 3P ETH-A
http://192.168.1.1
plug-in female connector strip with screw terminals,
4-pin, color green
+/– = connection for operating voltage
PE = connection for screen grounding
24 V DC
9 ... 28 V DC
62.5 mA (at 24 V DC)
1.5 W (at 24 V DC)
yes
yes, for screen grounding
0.14 ... 2.5 mm²
0.5 ... 0.7 Nm
7 mm
IEEE 802.11 n/g/b
2.4 ... 2.4835 GHz
<100 mW
max. 150 Mbit/s
WEP, WPA-PSK, WPA2-PSK
integrated
RP-SMA socket for external antenna connection
RJ45 socket, ports P1, P2 and P3
Twisted pair 10/100BaseT
PE connection (at operating voltage connection)
for fixed installation in closed housings, distributors and
switch cabinets, in interior rooms and dry rooms,
weather-proofed, unregulated
-20 ... +60 °C
5% to 93%
not permitted
mounting on TH 35-7.5 DIN rail
Preferably at the start or end of the mounting rail due to
the integral antenna, not in metal housings.
As required, including metal housings; External antenna
positioned outside the housing
approx. 106 g
approx. 110 g
22.5 × 101.5 × 91.5 mm
22.5 × 101.5 × 101.5 mm
EN 61000-6-2, EN 300328, EN 301489-1
(not included in delivery)
in the register
EN