Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating instructions
PA boxes wall mount
Item no. 1377588
Intended use
The product is intended for mounting a speaker (with 35 mm flange) to a wall. The weight of the
speaker must not exceed 40 kg.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the
product for purposes other than those described above, the product may be damaged. Read the
instructions carefully and keep them. Make this product available to third parties only together
with its operating instructions.
This product complies with the statutory national and European requirements. All company names
and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Wall mount
• 6 x screws
• 6 x dowels
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on proper
handling in this manual, we assume no liability for any resulting personal injury or
damage to property. Such cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• The product is intended for use in dry indoor spaces only.
• Assembling the product in an unsuitable location can lead to property damage and
personal injury!
• Use caution when assembling or mounting the product. Some edges of the product
are very sharp. Risk of injury!
• Perform the installation very thoroughly. The speaker or wall mount falling down
might not only cause expensive consequential damage but can also increase the
risk of injury!
• Check all screw connections from time to time. Modifying or moving the speaker or
wall mount can cause the screw connections to become loose over time.
• Do not over-tighten the screws. That could cause damage to the threads and affect
the strength of the screws.
• Do not use the product as a means to support yourself or hold on to.
• Do not attach any objects to the product other than the intended speaker.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
Installation
Wall mounting is only permissible if the condition of the wall is suitable to do so. Thin
light construction walls or gypsum plasterboards with unstable substructure are
usually not suitable. Nevertheless, there might be special dowels for such mounting
locations available in specialist shops. Contact a professional before installation in
case of doubt.
Use suitable mounting material (screws, dowels, etc.) depending on the surface (e.g.
concrete). The screw set provided is suitable for massive walls. The delivery scope of
the speaker wall mount does not contain special dowels or screws, and such must be
purchased separately depending on the surface structure.
Ensure a stable installation keeping in mind the weight of the speaker and wall mount
as well as the leverage effect.
Select the mounting location carefully, in order for the wall mount and the speaker
attached to it to be at the desired position (height and location) after installation.
When drilling or tightening screws, make sure not to damage any cables or pipes in the
wall. Accidentally drilling into electrical wiring poses a risk of fatal injury due to
electric shock!
Keep your own safety in mind when handling power tools (e.g. power drill). Observe all
other safety instructions in the manufacturer's instructions.
When installing the product, make sure there are no persons present within the area
below the speaker wall mount or the speaker box.
• Position the product at the wall and align it with a water level.
• Mark the 6 required boreholes on the wall and drill the holes into the wall.
• Screw the product to the wall. If necessary, use the provided screw set to do so.
• In order to adjust the arm length, loosen the knurled screw (1) and push the safety bolt (2)
towards the inside. Adjust the arm to the desired length and let the safety bolt lock into the
corresponding hole. Then retighten the knurled screw.
• In order to adjust the tilting angle of the complete arm, loosen the knurled screw (5) and push
the safety bolt (4) towards the inside. Adjust the angle as desired and let the safety bolt lock into
the corresponding hole. Then retighten the knurled screw.
• In order to adjust the tilting angle of the flange adapter, push the safety bolt (6) towards the
inside. Adjust the angle as desired and let the safety bolt lock into the corresponding hole.
• To swivel the arm, loosen the nut on both joints (3). Swivel the arm to the desired position and
retighten both nuts.
• Place the speaker on the product.
6
Maintenance and cleaning
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions.
• The product is maintenance-free and does not require any care except for occasional cleaning
with a soft, dry cloth.
Disposal
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.
Technical data
Load ................................................................max. 40 kg
Speaker flange .............................................35 mm
Operating conditions ...................................-20 to +50 °C, 0 – 75 % RH
Storage conditions.......................................-20 to +50 °C, 0 – 75 % RH
Arm length .....................................................385 – 535 mm
Length ............................................................425 mm
Width ..............................................................123 mm
Height .............................................................340 mm
Weight ............................................................3.3 kg
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
1
2
3
5
4
V2_1215_02-ETS-Mkd
Werbung
