Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Bij het winterklaar maken is het gebruikelijk om het waterpeil tot
onder de afzuiger en de lamp te laten zakken. Voor verplaatsbare
zwembaden: verwijder de voeding van het apparaat door de stekker
met drie pinnen die aan de voedingskabel vastzit, uit het stopcontact
te halen. Voor vaste zwembaden: schakel de voeding voor de lichtkring
uit bij de meterkast.
Ontkoppel de snelkoppeling op de kabel, schroef de kop van de lamp
uit de muurflens en berg hem op voor het volgende seizoen.
Gooi deze handleiding niet weg. Geef de handleiding door aan de
nieuwe eigenaar wanneer het product van eigenaar wisselt.
ENGLISH
Warning
Before installing this product, read and follow all warning notices and
instructions accom-panying this light. Failure to follow safety warnings
and instructions can result in severe injury, death, or property damage.
Important Notice
Attention Installer. This manual contains important information about
the installation, operation and safe use of this product. This information
should be given to the owner/operator of this equipment.
1. IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety
precautions should always be followed, including the following.
This light can be installed on storable above ground or permanent
above ground pools.
A permanent pool has a maximum water depth of over 42 inches. Do
not install on therapeutic pools, hydromassage bathtubs, spas or hot
tubs.
To reduce the risk of electric shock, if any cord becomes damaged,
return the entire transformer assembly for repair or replacement.
Risk of electrical shock. Connect only to a grounding type circuit
protected by a ground fault circuit interrupter (GFCI). Contact a licensed
electrician if you cannot verify that the receptacle or circuit is protected
by a GFCI. Do not use an extension cord.
Locate your pool so that the wall is at least 10 feet from all electrical
receptacles and at least 20 feet from all receptacles not protected by a
GFCI. The pool must also never be located under any lighting fixture or
within five (5) feet measured horizontally from any fixture mounted less
than five (5) feet vertically above the pool water level.
Risk of injury. Install the top of the lens with a minimum of 8 inches and
a maximum of 10 inches below top of pool wall or in manufacturer's
pre-punched return fitting hole.
Warning
Risk of electric shock. Disconnect power before servicing this unit.
Failure to disconnect power can result in death or severe personal
injury. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GFCI. Failure to
do so can result in serious personal injury and /or death.
2. TECHNICAL DETAILS
» Mounts easily into your return fitting.
» Does not restrict water flow.
» 6 pieces of high-quality diodes (LED).
» Equipped with transformer 230VAC input and 12VAC output 6W.
» Total cord length 7M. For steel wall above ground pool or wooden pool.
4
» Specification for transformer: Input:230V 50HZ; Out-put:12V 500MA 6W
3. INSTALLATION
For existing pool: Drain water level to be below the returning fitting.
1. Unscrew the light assembly head from the threaded wall flange.
See figure 1
Position 1: 1 ½" Fitting
Position 2: O-Ring Position
3: Washer Position
4: Big Rubber Gasket Position
5: Light Assembly Head
Warning: Please do not open the light assembly head. Open the head
will void the warranty.
2. Remove the existing eyeball fitting including eyeball, eyeball nut &
eyeball base from the return fitting on your pool wall
See Figure 2
Position 1: Hose
Position 2: Pool Wall
Position 3: Liner
Position 4: Existing Eyeball
Position 5: Hose Adaptor
Position 6: Return Fitting Nut
3. Screw the light assembly head in the threaded wall flange. Make sure the
big rubber gasket is installed to prevent the damage to the line.
See Figure 3
Position 1: 1 ½" Fitting
Position 2: O-Ring
Position 3: Washer
4. Connect 1.5" fitting to the light assembly head and make sure an o-ring is
installed and screw it tight enough to pre-vent any leaking.
See Figure 3
Position 1: 1 ½" Fitting
Position 2: O-Ring
Position 3: Washer
5. Disconnect the clamp on the hose. Unscrew the hose adap-tor from the
existing fitting and screw to a 1.5" Fitting.
See Figure 4
Position 1: Hose Adaptor
Position 2: 1 ½" Fitting
Position 3: Pool Wall
Position 4: Light Assembly Head
6. Connect the hose to the hose adaptor.
See Figure 5
Position 1: Hose
Position 2: 1 ½" Fitting
Position 3: Pool Wall
Position 4: Hose Adaptor
Position 5: Light Assembly Head
7. Connect the quick wire connection as Figure 6.
4. STORAGE AND WINTERIZING INSTRUCTIONS
EN
Werbung
