Omnitronic IC PRO Serie Bedienungsanleitung

USER'S MANUAL
STUDIO MICROPHONE
Professional tube condenser microphone
The IC-1005 PRO / IC-1010 PRO was designed for professional studio recording and live applications.
The microphones operate on the included power units.
Ideal as main and support microphone for vocals or guitars
Far more clarity and accuracy than dyanamic microphones
Cardioid pickup pattern for effective feedback elimination
Low-noise transformerless FET input eliminates low frequency distortion
Balanced XLR output
Safety Instructions
Maintenance and service operations are only to be carried out by authorized dealers. Damage,
caused by manual modifications on these devices are not subject to warranty. If the microphone
or the power supply unit is used for other purposes than originally intended or if it is not correctly
connected, the products may suffer damages and the guarantee becomes void.
Protect the devices against humidity and heat. The ambient temperature must always be between
-5° C and +45° C. The relative humidity must not exceed 50 % with an ambient temperature of
45° C. The microphone must be powered by the included power supply unit. Caution! This unit
requires hazardous mains voltage. Be careful with your operations. The power supply unit is
allowed to be operated with an alternating current of 115 V or 230 V AC, 50 Hz and was designed
for indoor use only. This device falls under protection-class I. The power plug must only be
plugged into a protection class I outlet. The voltage and frequency must exactly be the same as
stated on the device. Wrong voltages or power outlets can lead to the destruction of the device
and to mortal electrical shock.
Setting into Operation
Screw the shock mount on your microphone stand and insert the microphone from above.
Connect the microphone to the MIC IN jack of the power supply unit with the supplied 7-pin XLR
cable.
Connect the OUTPUT jack of the power supply unit to the XLR microphone input of your audio unit
(e.g. mixing console) using a balanced microphone cable with 3-pin XLR plug.
Plug the supplied power cord into the AC IN jack of the power supply unit. Make sure the
voltage selector is properly set! Connect the power plug to the mains.
Turn on the device via the power switch.
Cleaning and Maintenance
For cleaning the microphone and the power supply unit only use a soft lint-free and moistened cloth.
Make sure not to allow any water to enter the devices and never use any solvent cleansers.
If the fine-wire fuse of the power supply unit fuses only replace the fuse by the same type and
rating. The correct value of the mains fuse is specified on the device. Before replacing the fuse,
unplug mains lead.
© Copyright
Nachdruck verboten!
Reproduction prohibited!
Delivery Includes
Technical Specifications
IC-1005 PRO / IC-1010 PRO
Type:...................................Condenser
Polar pattern: ......................Cardioid
Sensitivity: ......................... -34 dBu @ 1 kHz
Equivalent SPL: .................13 dBA, 20 dBC
Max. SPL: ...........................140 dB (THD <0.5% @ 1 kHz)
Nominal impedance: ..........250 o hms
Load impedance: ...............200 o hms
Output impedance: .............1000 o hms
Power supply: .....................48 V DC phantom power
Connection: .......................7-pin XLR, balanced
Power supply unit
Power supply: .....................115/230 V AC, 50/60 Hz ~
Power consumption: ...........10 W max.
Input and Output: ...............7-pin XLR, balanced
Output:................................3-pin XLR, balanced
Dimensions (LxWxH): .........167 x 102 x 61 mm
Weight: ...............................1.2 kg
frequency response (cardioid)
Please note: Every information is subject to change without prior notice. 10.05.2007 ©
IC PRO SERIES
I C-1005 PRO / IC-1010 PRO Studio Mic
Foam-lined carrying case
Foam-lined wooden box
Shock mount
Power supply unit
10m XLR cable
polar pattern (cardioid) at 1 kHz
13030702_V_1_0.DOC
www.omnitronic.com