Renkforce 1403557 Bedienungsanleitung Seite 2

G Operating instructions
USB 3.0 Hub for Microsoft
Item no. 1403557
Intended use
The product is intended to be connected to a USB3.0 port of a Microsoft
Pro 2 and 3.
There it provides 2 additional USB3.0 ports. Additionally, a card reader for SD and
microSD memory cards is integrated.
Power supply to the product and data transfer is realised via USB.
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owners. All
rights reserved.
Carefully read the entire operating instructions which contain important information
about operation and use. Observe all safety instructions!
Package contents
• USB 3.0 Hub for Microsoft Surface
®
• Operating instructions
Up-to-date operating instructions:
1. Open www.conrad.com/downloads in a browser or scan the
displayed QR code.
2. Select document type and language and enter the item num-
ber into the search field. After submitting the query you can
download displayed records.
Safety instructions
Damage due to not following these operating instructions will void the
warranty. We do not assume any liability for any resulting damage!
We do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions. In such
cases, the warranty will be null and void!
Dear customer,
the following safety instructions and hazard warnings are intended not only
to protect your health but also to protect the device. Please read the follow-
ing points carefully:
• For safety and licensing reasons (CE), unauthorised conversion and/or
modification of the product is not permitted.
• The product is not a toy and does not belong in the hands of children.
• The product may be used in dry, enclosed indoor areas only; it must not
get damp or wet.
• The product must not be exposed to extreme temperatures, strong vibra-
tions or heavy mechanical stress.
• Do not leave packaging material carelessly lying around, since it could
become a dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts, blows, or
accidental falls, even from a low height.
• If you have any questions that are not answered in these operating in-
structions, please contact our technical support centre or consult a pro-
fessional.
Surface
® ®
®
Connection and start-up
• Connect the product to a free USB3.0 port of your Microsoft
does not matter if it is switched on or off.
When the USB3.0 hub is supplied with power, the blue LED on the upper side
lights up.
The operating system will detect the new hardware, and automatically install the
required driver; it is already present in the operating system.
• Now connect your USB devices to the two USB3.0 ports. Depending on the USB
device, the driver might have to be installed manually.
The USB3.0 ports are backwards compatible with USB2.0 and USB1.1.
Using memory cards
The integrated card reader has a slot for SD cards and microSD cards. The memory
card used is integrated into the system in the same way as a conventional removable
media drive. When the memory cards are accessed for reading or writing, the blue
LED on the hub/card reader flashes.
It is not possible to use SD cards and microSD cards at the same time. Only
Surface
® ®
one type of card can be used at any one time.
Inserting and removing a memory card
• Pay attention to the correct polarity when inserting a memory card.
When inserting an SD card, the contacts must point towards the microSD card slot.
When inserting a microSD card, the contacts must point towards the SD card slot.
The write protection (sliding switch on the memory card) must be deactivated
for data to be written to or deleted from the SD card.
• When the memory card is to be removed, wait until all read/write accesses have
finished (The LED on the card reader stops flashing and remains lit permanently).
Only then pull out the memory card carefully from the card slot.
If the memory card is pulled out while data are still read or written, the data
on the memory card can be corrupted. It might also be necessary to refor-
mat the memory disk.
The same applies for disconnecting the USB connection.
Maintenance and cleaning
• The product does not require any maintenance.
• The product exterior should be cleaned only with a clean, soft, dry cloth.
Do not use abrasive cleaning agents, cleaning alcohol or other chemical
solutions, since these could damage (discolour) the housing or even impair
operation.
Disposal
The product must not be disposed of in household waste!
Dispose of the waste product in accordance with the applicable legal regu-
lations.
Technical data
Operating voltage...............................5 V/DC
Power supply ......................................USB3.0
USB standard...................................... USB3.0 (backwards compatible with USB2.0 and
Connections ........................................ 1 USB3.0 plug; 2 USB3.0 sockets; 1 SD card slot;
Supported memory cards ................. SD; SDHC; SDXC; max. 128 GB
Supported devices ............................. Microsoft
Supported operating systems .......... Windows
Dimensions (W x D x H)..................... approx. 70 x 33 x 9 mm
Weight .................................................. approx. 13 g
Operating and storage conditions... 0 °C to +40 °C; 20% to 80% relative humidity
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2016 by Conrad Electronic SE.
Surface
®
USB1.1)
1 microSD card slot
Surface Pro 2 and 3
® ®
XP from SP1 (only 32 bit); Windows
®
Vista , Windows 7, Windows 8, Windows
TM ® ®
Windows 10, (32 und 64 Bit); Windows
®
Pro 2 or 3. It
®
®
8.1,
®
RT
®