Werbung
Čeština
Jakmile je 2,5 " SATA pevný disk sestaven, je vysoce
doporučeno, že to není možné rozebrat. Jakékoli
poškození, ke kterému dochází při demontáži se
nevztahuje záruka
JEE253 Krok
1
Otevřete externí pevný kryt disku a
2
Umístěte pevný disk SATA v
připojení 2,5 "SATA pevný disk ke
zadním krytu pevného krytu
konektoru SATA na základní
frekvenčního měniče.
desce.
3
4
Put přední straně pevného krytu
Umístěte gumový kryt kolem
jednotky na horní a upevnit dva
pevného krytu disku.
šrouby.
Instalace hardware
JEE251
JEE252
Magyarország
Amint a 2.5 "SATA merevlemez áll össze, akkor erősen
ajánlott, hogy nem szedhető szét. Minden kár, amely
akkor szétszerelés közben nem vonatkozik a garancia
JEE251 lépés
1
2
Nyissa ki a külső merevlemez ház
Helyezze a SATA merevlemezt a
és csatlakoztassa a 2,5 "SATA
hátlapot a merevlemez ház.
merevlemezt a SATA csatlakozót
az áramkör.
3
4
Tedd az első a merevlemez ház
Helyezze a gumi burkolat körül a
tetejére, és rögzítse a két
merevlemez ház.
csavarral.
A hardver telepítése
JEE251
JEE252
2.5'' SATAハードディスクドライブが組み立てられると、
それは非常にそれを分解しないことをお勧めします。 分
解時に発生した損傷は保証の対象にはなりません。
JEE251
インストール手順
1
外付けハードディスクカートリッ
ジシェルをオンにし、ボードと2.5
"SATAハードディスクの接続をピッ
クアップ。
3
ハードディスクカートリッジロッ
クの上部にある2本のネジが。
ハードウェアのインストール
PC
一旦2.5'' SATA硬碟組裝，強烈建議，不要將其拆卸。
如在拆卸過程中發生的任何損壞均不在保固之內
JEE251
安裝步驟
1
打開硬碟盒殼，拿起電路板與2.5吋
SATA硬碟連接。
3
將硬碟盒背面上方的兩個螺絲鎖緊。
硬 體 安 裝
PC
日本 語
2
背面のハードドライブを交換しま
す。
4
スリーブは、外付けハードドラ
イブ上のゴム製保護ケースがあ
ります。
PC
JEE251
JEE252
繁體中文
2
放回硬碟盒的背板裡。
4
把橡膠保護套，套在硬碟盒上。
PC
JEE251
JEE252
Limited Warranty
j5create offers a limited 1-year warranty. User's wear & tear damage is not included.
The user shall call or email j5create customer service with the defect information of the product and
obtain a return authorization number. Users are responsible for one way return freight cost and we will
take care of one way freight back. In order to obtain a return authorization number, users should have
the following information handy when calling or emailing the service team:
(i) a copy of the original purchase invoice to verify your warranty
(ii) a product serial number
(iii) a description of the problem
(iv) customer's name, address, and telephone number
j5create does not warrant that the operation of the product will be uninterrupted or error-free. j5create
is not responsible for damage arising from failure to follow instructions relating to the product's use.
This warranty does not apply to:(a) consumable parts, unless damage has occurred due to a defect in
materials or workmanship; (b) cosmetic damage, including but not limited to scratches, dents ,and
broken plastic on ports; (c) damage caused by use with non-j5create products; (d) damage cause by
natural disasters ( flood, fire, earthquake, lighting strike, typhoon etc.,)(e) damage caused by human
misuse( lost, accident, abuse, misuse or other external causes) (f) damage caused by operating the
product outside the permitted or intended uses described by j5create ; (g) damage caused by service
(including upgrades and expansions) performed by anyone who is not a representative of j5create or a
j5create Authorized Service Provider; (h) a product or part that has been modified to alter functionality
or capability without the written permission of j5create; or (i) if any j5create serial number on the
product has been removed or defaced.
If such a situation occurs, j5create will calculate the cost of materials and repair for your reference. This
warranty is given by j5create in lieu of any other warranties expressed or implied.
Copyright© 2015 j5create. All rights reserved. All trade names are registered trademarks of their
respective owners. Features and specifications are subject to change without notice. Product may not
be exactly as shown in the diagrams.
Regulatory Compliance
FCC
This equipment has been tested and found to comply with FCC Part 15 Subpart B and Canada Standard
ICES-003 Issue 5, Class B, ANSI C63.4: 2009
Operation is subject to the following two conditions:
• This device may not cause harmful interference
• This device must accept any interference, including interference that may cause undesired operation
of the device.
CE
This equipment is in compliance with the requirements of the following regulations:
European Standard EN 55022:2010/AC: 2011 Class B,
EN61000-3-2:2006/A1: 2009 and /A2: 2009 , EN61000-3-3: 2008 and EN55024: 2010 (IEC61000-4-2:
Edition 2.0 2008-12
IEC61000-4-3: Edition 3.2 2010-04 , IEC61000-4-4: Edition 3.0 2012-04, IEC61000-4-5: Edition 2.0
2005-11, IEC61000-4-6: Edition 3.0 2008-10 , IEC61000-4-8: Edition 2.0 2009-09 , IEC61000-4-11: Edition
2.0 2004-03)
C-Tick
This equipment is in compliance with the requirements of the following regulations:
AS/NZS CLSPR 22:2009/Amdt 1:2010
Werbung
