Technical Specifications; Care And Maintenance; Disposal Information - Hudora Rx Aufbau- Und Bedienungsanleitung

INSTrUcTIoNS For ASSEmBLY AND USE
coNGrATULATIoNS oN YoUr PUrcHASE!
Please read this user guide carefully. The user guide is an essential part of the
product. Please keep it carefully along with the packaging in case you have any
queries at a later date.
If you are giving this product to another person, please ensure that they receive
this user guide too. Children assembling, using or repairing the product should
always be supervised by an adult.

TEcHNIcAL SPEcIFIcATIoNS

Article: Roller RX
Article number: 11026
Maximum dimensions: 123 x 65 x 95 cm
Max. user weight: 50 kg
Weight: 7,6 kg
Handlebar adjustable between:
You will find answers to frequently asked questions and solutions to many
technical problems under: http://www.hudora.de
coNTENT:
1 frame with rear wheel and brake
1 front wheel with axle and axle screw
1 front mudguard
1 steering column with hand-operated brake cables
1 bag of screws, washers, bolts, shock absorbers and tools
1 user guide
Other parts supplied are not necessary for assembly and use.
ASSEmBLY INSTrUcTIoNS:
The scooter must be assembled by an adult.
(1) Start by unscrewing the axle nuts. The brake cable channel (A) must also
be loosened (see fig. (II)). Place the front wheel in the axle opening of the
steering column fork and place the retaining ring and mudguard bracket on the
axle before tightening the axle with the bolt. Make sure that the axle is straight
and that there is enough space between the wheel and the mudguard.
(2) Attach the mudguard to the frame. The screw is guided through the fork
and then through the mudguard bracket from the front. Finally, place the was-
her on the screw and tighten the bolt firmly.
(3) In order to attach and adjust the steering column, make sure that the front
fork is inserted into the frame facing in the direction of travel as in fig. (I). The
steering column is then inserted into the frame tube. When doing this, ensure
that it is parallel to the front wheel and that the handlebars are set at the
required height. The steering column may not be pulled out any further than
the groove marked MAX. In order to fasten the steering column, the screw
at the top end of the steering column tube must be tightened. To do this, it is
best to stand in front of the scooter with the front wheel gripped between your
legs and tighten the screw so firmly that the steering function can be safely
guaranteed. Finally, the brake cable is again guided through the cable channel
and the brake function is tested. This may have to be adjusted.
82 - 95 cm
HUDORA GmbH • Jägerwald 13 • 42897 Remscheid • GERMANY
http://www.hudora.de
INSTrUcTIoNS For ADJUSTING THE BrAkE SYSTEm:
The brake system is pre-assembled at the factory and should be tested and
if necessary adjusted before using the scooter. How to do this: check that
the brake blocks are lying evenly on the rim flank. If this is not the case, you
can adjust them by releasing the brake shoe screw (B). The recommended
distance between the rim and the brake block is approx. 1.5 to 2 mm. If the
distance is larger or smaller, you can change it by turning the adjusting screw
(C) (screwing it in will decrease the braking force! Screwing it out will increase
the braking force!). If the distance from the brake blocks is too great, the
brake cable should be adjusted by loosening the nut at clamping screw (D) and
pulling it through as required.
ImPorTANT! Whenever you work on the brake, it is crucial that you check
whether all the screws are tight and that the brake is actually working. Defec-
tive brakes are a tremendous hazard and may cause accidents!
Cable channel (A)

cArE AND mAINTENANcE:

Only use a cloth or damp rag to clean the product; do not use harsh cleaning
agents!Check the product for damage and wear and tear before and after use,
and repair this at once. Make sure that all screws on movable parts such as
the axle and steering column are tightened firmly and cannot loosen while tra-
velling. Store the product in a safe place protected from the climate, so that it
cannot be damaged. For your own safety, make sure that you only use original
spare parts. You can order these from HUDORA.
Do not make any structural changes. Should any parts be damaged or any
sharp corners and edges have formed, use of the product should be disconti-
nued. If in doubt, contact our service department (http://www.hudora.de).

DISPoSAL INFormATIoN

At the end of the product's life, please make use of the available return and
collection systems. The disposal company will answer questions on site.
SErVIcE:
We make every effort to supply products which are in perfect condition.
However, should defects be found, we also make every effort to repair these.
You will therefore find extensive information about the product, spare parts,
trouble-shooting and mislaid user guides at http://www.hudora.de.
You will find answers to frequently asked questions and solutions to many
technical problems under: http://www.hudora.de.
wArNING! Not suitable for children under 3 years because of the risk of
swallowing small parts!
Clamping screw (D)
Brake shoe screw (B)
Adjusting screw (C)
Art. no. 11026
Status 01/10
Page 2/8