WOODLAND JUST PLUG LIGHT HUB JP5701 Anweisungen

JUST PLUG
INSTRUCTIONS
BEFORE YOU PROCEED
Read through instruction booklet entirely. Comply with all operating instructions. Failure to follow instructions could result in damage to the
product or personal injury. Do not modify or tamper with any electronic components. Combine products from the Just Plug Lighting System
only, unless otherwise instructed. Save these instructions.
GETTING STARTED
The Just Plug Lighting System is made up of Ports, Plugs and Cables. This simple
connection system makes it quick and easy to light one building or an entire city.
How to Connect a Plug to a Port
Align locking tabs on Plug with front of Light Hub, Sequencing Light Hub or
Expansion Hub. Insert Plug into Hub Port until locking tabs click into place (Fig. 1).
How to Remove a Plug from a Port
Grasp top edge of Plug and pull firmly.
LIGHTS & HUB SET (JP5700), LIGHT HUB AND SEQUENCING LIGHT HUB (JP5680)
Light Hubs and Sequencing Light Hubs supply power to Just Plug LED Lights.
• To power Light Hub and Sequencing Light Hub, insert Power Supply (JP5770-JP5773) plug into POWER IN Port (or use a 16-20VAC
or 24VDC train power pack, Fig. 5).
• Do NOT remove CTRL Port Plug (unless using Auxiliary Switch (JP5725) or connecting to DCC).
• Plug LED Lights (JP5736-JP5749, JP5754, JP5755), Port Sharing Device (JP5681), Linker Plugs (JP5685) or Built-&-Ready
Buildings into LIGHT Ports.
• Lights & Hub Set includes two Stick-On Lights. To secure Lights in building, remove release paper from back of LED and stick on
where desired.
• Rotate Dimmer Controls to adjust light brightness (adjusts from very bright to off).
• Use dedicated spaces on front of Hub to label according to your lighting configuration.
• To mount Hub, use included Tape or Screws.
SEQUENCING LIGHT HUB – HOW TO SEQUENCE LIGHTS
The Sequencing Light Hub automatically switches LED lights on and off in sequence, just like they would in a real city's nightscape. When multiple
Sequencing Light Hubs are used on a layout an even more random effect can be achieved.
To initiate sequence:
1. Turn ON/OFF switch to ON.
2. On SPEED Dial, "S" = Slow / "F" = Fast. Rotate Dial to increase or decrease the speed of lights turning on and off.
IN CTRL
EXPANSION HUB (JP5702)
Connect Light Hubs and Sequencing Light Hubs to Expansion Hub to expand your lighting system.
POWER
CAUTION: Do not plug LED Lights into Expansion Hub.
• To power Expansion Hub, insert Power Supply (JP5770-JP5773) plug into POWER IN Port (or use a 16-20VAC or 24VDC train power
LIGHT HUB
pack, Fig. 5).
• Do NOT remove CTRL Port Plug (unless using Auxiliary Switch (JP5725) or connecting to DCC).
• Use included Connecting Cables to connect to Light Hubs (Fig. 2), Sequencing Light Hubs, another Expansion Hub (Figs. 3 and 4),
train power pack (Fig. 5) or DCC relay unit (Fig. 6).
• Use dedicated spaces on front of Hub to label according to your lighting configuration.
• To mount Hub, use included Tape or Screws.
1
CONNECTING HUBS TOGETHER
Use Connecting Cables (included with Expansion Hub)
Connect Light Hubs and Sequencing Light Hubs to Expansion Hub
Insert Connecting Cable Plug into Expansion Hub HUB Port and opposite Plug into Light Hub or Sequencing Light Hub POWER IN
Port (Fig. 2).
Connect Expansion Hub to Expansion Hub
Insert Connecting Cable Plug into POWER OUT Port on powered Expansion Hub. Insert opposite Plug into POWER IN Port on add-on
Expansion Hub (Fig. 3). Keep expanding your lighting system (Fig. 4).
Power Hubs from a Train Power Pack
Cut off one Connecting Cable Plug with wire cutters and strip approximately 1" of wire. Connect bare wires to the accessory terminals
on a 16-20VAC or 24VDC power pack. Insert Plug on other end of Connecting Cable into Hub POWER IN Port (Fig. 5).
Control Just Plug Lighting System with DCC
Cut off one Connecting Cable Plug with wire cutters
and strip approximately 1" of wire. Connect bare
wires to DCC relay unit (follow DCC manufacturer
instructions for proper installation of wires). Insert
Plug on other end of Connecting Cable into Hub
CTRL Port (Fig. 6). CAUTION: Verify Connecting
Cable is plugged into the CTRL Port before applying
power.
TIP! For additional realism, install Sequencing
Light Hubs in combination with Light Hubs to
light buildings. Use Light Hubs to light buildings
where you want to show nighttime occupants
still bustling around the office or home. Use the
Sequencing Light Hub to light buildings where
occupants are turning lights ON/OFF. Use the
Masking Paint in Light Block Kit (JP5716) to black
out a few windows for added realism.
4
directamente a las luces LED cuando está en funcionamiento. / VORSICHT: Schauen Sie nicht direkt
in die aufleuchtende LEDs.
RoHS Compliant
WOODLAND SCENICS
LIGHT
No.
4
2 3
LIGHTS & HUB SET (JP5700) AND LIGHT HUB (JP5701)
Power
Supply
Screw
Hole
CAUTION: Do not look directly into LED lights when in operation. / ATTENTION : Ne pas
regarder directement dans les lumières LED en fonctionnement. / PRECAUCIÓN: No mire
WOODLAND
Manufactured by
®
LIGHTING SYSTEM
®
LIGHT HUB JP5701
locking
Fig. 1
Ports
tabs
Plug
IN CTRL
POWER LIGHT
LIGHT HUB
No.
DIMMER CONTROLS
1 2 3 4
WOODLAND SCENICS
IN OUT CTRL
POWER HUB
EXPANSION HUB
No.
WOODLAND SCENICS
LED Stick-On Light, Nano
LED Light, Port Sharing
Device, Linker Plugs,
Built-&-Ready Buildings
CTRL
Port
Light Ports
Plug
Screw
Hole
1a 1b 1c 1d
1
Dimmer Controls
Model making product. Not a toy! Not suitable for children under 14 years! / Produit
pour le modélisme. Pas un jouet! Pas adapté aux enfants de moins de 14 ans! / Producto
para modelismo. No es un juguete! No adecuado para niños menores de 14 años! /
Modellbauartikel. Kein Spielzeug! Nicht geeigent für Kinder unter 14!
• PO BOX 98, LINN CREEK, MO 65052 • M8 • woodlandscenics.com
®
Power
Supply
Power
Supply
Connecting
Cable
Power
Connecting
Supply
Cable
Expansion
Hub
®
Fig. 4
1a 1b 1c 1d 1a 1b 2a 2b 2c 2d 2a 2b 2c 2d 1c 1d
1 1 2 2
1 2
Connecting
Cable
Fig. 6
Power
Supply
Connecting
Cable
Power
Supply
SEQUENCING LIGHT HUB (JP5680)
Power
Supply
Screw Hole
1
Flip switch
to ON position to
Sequence Lights.
Turn OFF to stop
sequence
Slowest Speed
Connecting
Cable
Sequencing
Light Hub
Light
Hub
Fig. 2
1a 1b 1c 1d
1
Fig. 3
Expansion
Hub
3a 3b 3c 3d 4a 4b 4c 4d 5a 5b 5c 5d 5a 5b 5c 5d 1a 1b 1c 1d
3 4 1 5 5
Keep
Expanding
3 4 5
1 2
Train
Power
Pack
Fig. 5
Connecting
Cable
DCC
Relay
Unit
DCC Relay Unit
CTRL
Port
Plug
Light Ports
Screw
Hole
2a 2b 2c 2d 1a 1b 2a 2b 2c 2d 1a 1b 1c 1d 1c 1d
1 2
1 2
Dimmer Controls
2
Rotate Dial
to alter speed of
sequence
SPEED Dial
indicator
Fastest Speed