Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Quicklinks
INSTRUCTIONS & PARTS LIST FOR 1410, DR1412, DR1414 & DR1416 AIR DRILLS
Read and understand "Safety Instructions For Air Tools" and these instructions before
Tools left connected to the air supply while making adjustments, changing accessories, or doing any mainte-
Always remove tool from air supply and activate trigger to bleed air line before making any adjust-
ments, changing accessories, or doing any maintenance or service on tool.
AIR SUPPLY
The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pressure regulator, and
lubricator will insure maximum output and service life of tools.
HOSE AND HOSE CONNECTIONS
Supply hose should be not less than 5/16" (7.9mm) I.D. Extension hoses should be at least 3/8" (10mm) I.D. Use couplings and fittings with at least
5/16" (7.9mm) I.D.
LUBRICATION
An airline lubricator, set to deliver one drop per minute, is recommended. If a lubricator is not used, add .04oz. (1.2cc) of SIOUX No. 288 air motor oil
into the air inlet daily.
Lubricate the gearing with SIOUX No. 1232A grease after every 50 hours of operation.
GENERAL OPERATION
This tool is equipped with a teasing throttle. By slightly depressing the trigger the chuck will rotate slowly. This is useful for starting a drill bit without
first spotting with a punch. Fully depressing the trigger for maximum speed.
A speed control adjusting screw is located on the trigger face and is adjusted with a 1/16" (1.6mm) hex key wrench.
We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products
1410, DR1412, DR1414 & DR1416
to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:
April 1, 2006
Murphy, North Carolina, USA
Date and place of issues
SERIAL "D"
operating this tool.
nance or service on tool can start unexpectedly.
Tools starting unexpectedly can cause injury.
SOUND AND VIBRATION READINGS
Sound Pressure
Catalog No.
dBA
1410
72.5
DR1412
72.5
DR1414
72.5
DR1416
72.5
*prt PN8NTC1
DECLARATION OF CONFORMITY
Includes products with A, LC, & Y in the catalog number
EN 792 (draft), EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1
following the provisions of
89/392/EEC as amended by 91/368/EEC & 93/44/EC Directives.
Mark S. Pezzoni
President
Power and Specialty Tools
Name and position of issuer
Sound Power
Vibration
2
dBA
m/s
83.5
Less than 2.5
83.5
Less than 2.5
83.5
Less than 2.5
83.5
Less than 2.5
*prt PN8NTC1
*per ISO8662
Signature of issuer
1
Form ZCE430D
Date 2007June4/A
Page 1 of 10
Printed In U.S.A.
Werbung
Verwandte Anleitungen für Sioux Tools 1410
Inhaltszusammenfassung für Sioux Tools 1410
- Seite 1 *per ISO8662 DECLARATION OF CONFORMITY We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products 1410, DR1412, DR1414 & DR1416 Includes products with A, LC, & Y in the catalog number to which this declaration relates are in conformity with the following standard or standards or other normative document or documents: EN 792 (draft), EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1...
- Seite 2 *prtPN8NTC1 *gemäß ISO8662 KONFORMITÄTSERKLÄRUNG Wir, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, erklären hiermit alleinverantwortlich, daß die Produkte 1410, DR1412, DR1414 und DR1416 Schließt Produkte mit A, LC, & Y in der Katalognummer ein auf die sich diese Erklärung bezieht, mit den Anforderungen der folgenden Standards oder Normen oder Dokumenten übereinstimmen:...
- Seite 3 PN8NTC1 ISO8662 DECLARACION DE CONFORMIDAD Nosotros, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declaramos bajo nuestra única responsabilidad que los productos 1410, DR1412, DR1414 y DR1416 Incluye los productos marcados con una A, LC, & Y en el número de catálogo con los cuales se relaciona esta declaración están en conformidad con las siguiente(s) norma (s) u otro (s) documento(s) normativo(s):...
- Seite 4 *sec. PN8NTC1 *sec. ISO8662 CERTIFICAZIONE DI CONFORMITA’ La Sioux Tools, Inc, con sede al 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, solennemente dichiara sotto la propria e sola responsabilità che i prodotti 1410, DR1412, DR1414 e DR1416 Compresi i prodotti con A, LC, &...
- Seite 5 ISO8662 DECLARATION DE CONFORMITE La société Sioux Tools, Inc., située à : 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, affirme que les produits 1410, DR1412, DR1414 et DR1416 Inclure les produits dont le numéro de catalogue comporte la lettre A, LC, & Y dont cette fiche fait l’objet, sont conformes aux normes, documents normatifs et autres références :...
- Seite 6 *conf. PN8NTC1 *conf. ISO 8662 CONFORMITEITSVERKLARING Ondergetekende, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, verklaart met inachtneming van de eigen aansprakelijkheid desbetreffend, dat de produkten 1410, DR1412, DR1414 en DR1416 Inclusief producten met de letter A, LC, & Y in het catalogusnummer...
- Seite 7 *prtPN8NTC1 *enligt ISO8662 FÖRSÄKRAN OM ÖVERENSSTÄMMELSE Vi, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, förklarar under eget ansvar att produkterna 1410, DR1412, DR1414 och DR1416 Inkluderar produkter med A, LC, & Y i katalognumret som denna försäkran gäller uppfyller följande standard eller standarder eller andra normgivande dokument:...
- Seite 9 PARTS LIST FOR 1410, DR1412, DR1414 & DR1416 AIR DRILLS SERIAL “D” Fig. Part Fig. Part Description Description 21019A Chuck—1/4” Capacity (1410, DR1412) 21441 Spring 30202 Key—Chuck (1410,DR1412) 66300 Assembly—Trigger 21077 Chuck—1/4” Capacity (1410A) 14349 Ring—“O” 30000 Key—Chuck (1410A) 21542 Ring—Retaining 67217 Retainer 14311 Ring—“O”...
- Seite 10 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Der durch Elektrosanden, -sägen, -schleifen und -bohren sowie durch andere Bauarbeiten anfallende Staub enthält Chemikalien, die nachweislich Krebs sowie Geburts- bzw. andere Fortpflanzungsschäden hervorrufen.