Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operation manual
Intended Use
This product is intended for use as a wireless charging device for Qi-
enabled devices. To check if your device supports the Qi standard, read its
manual or contact the manufacturer. This device is intended for private,
non-commercial use only. The device should only be used in household or
similar environments. The device must not be used in environments with a
corrosive or explosive atmosphere or for medical purposes. The device
may only be used in accordance with these instructions for use. Any use
other than as described in this manual is considered improper use.
Changes in the course of technical progress are reserved.
Technical specifications:
Housing:
Plastic
Battery type:
Lithium-polymer battery
Input voltage / current:
5 V / 2,0 A
Output voltage / current:
5 V / 1.1 A / 10 W
Dimensions:
approx. 140 x 98 x 75 mm
Weight:
147 g
Safety note:
● Read all safety instructions and all instructions.
● Please take the time and read the general safety instructions. You will
find the general safety instructions in a separate brochure. This brochure
is included in the scope of supply.
Unpacking and checking content:
● Wireless Charger lamp Lasse
● USB Type C <> USB A connector cable
● Safety instructions
Product illustration:
1.
display hours
2.
display minutes
3.
night light
4.
M button
5.
"+" button
6.
"-" button
7.
Upper colons: Second indicator
8.
wireless charging area
9.
Wireless Charging Indicator
10.
type C input connection
11.
night light button
12.
USB Type A port
Use:
Wireless charging of compatible devices:
1. Connect the Type C USB port with the cable to the USB port of a
computer or an optional USB power adapter. When using a USB
charger, make sure to plug it into a suitable and easily accessible
power outlet.
2. Place your Qi-enabled device in the center of the Wireless Charger.
Charging starts automatically.
LED indicator:
- Power connection successfully completed: Blue light flashes twice
- Standby: indicator does not light up
- Charging process: The light illuminates blue continuously; as soon
as the device is fully charged, the light goes out.
- FOD (foreign object detection): The light flashes blue continuously.
3. If the charging process does not start automatically, please check the
following points:
- Remove all foreign objects between the two devices.
- Check if the power supply is compatible.
- Check whether your device is Qi-capable.
- Check whether the supplied charging cable is correctly connected
to the Wireless Charger or power supply / USB port at both ends.
- Check the correct position of the device to be charged. Please refer
to the corresponding operating instructions or contact the
manufacturer.
4. To complete the charging process, simply remove the device to be
charged from the wireless charger.
Charging compatible devices by cable:
Depending on the type, connect the device to be charged to the type A
port (12) using a suitable cable.
Alarm Clock functions:
The alarm clock is set with the M, +, - and night light (4, 5, 6 and 11)
buttons.
Setting the time:
Double-click the M button (4) to switch between 12 and 24 hours.
The 12-hour display shows "AM" in the morning and "PM" in the
afternoon.
Press the M button once to go to the minute setting. Use the + and -
buttons to set the minutes.
After you have set the minutes, press the M button again to go to the
hour setting. Now use the + and - buttons to set the hours.
Press the M button again to end the operation.
Setting the alarm:
Press the + button for 2 seconds to activate the alarm. To deactivate
the alarm, press the button for 2 seconds.
When the alarm is activated, an alarm icon appears on the display.
When the alarm is activated, press the M button for 3 seconds to go
to the minutes setting, then use the + and - buttons to set the
minutes.
After setting the minutes, press the M button again to go to the hour
setting. Now use the + and - buttons to set the hours.
Press the M button again to end the operation.
When the alarm sounds at the set time, press any button to turn it
off.
If no button is pressed, the alarm will automatically stop after 3
minutes.
Setting the Display Brightness:
The display has 3 automatic brightness levels:
Maximum brightness from 7 to 19 o'clock
Average brightness from 19 to 0 o'clock
Minimum brightness from 0 to 7 o'clock
The brightness of the display can also be changed manually.
Deactivate the alarm
Use the + and - buttons to change the brightness to 4 levels
(Maximum, Medium, Minimum and Off).
The manual changes are automatically adjusted again at the above
times.
Setting the Night Light:
The night light can be adjusted in 3 different brightness levels.
Press the night light button (11) once to turn on the night light. The
lowest brightness is set.
Press the nightlight button again to set to medium brightness.
Press the nightlight button again to set the highest brightness.
Press the nightlight button again to turn off the night light.
Notes:
The Wireless Charger Alarm Clock Alina has a built-in battery. This is
only used for the functions of the clock. All functions are deactivated
if the power supply is interrupted. The functions are restored when
the power is reactivated.
To use all functions of the product (Alarm Clock, Wireless Charging,
Night Light & USB Type A Output) in parallel, the product should be
operated with a QC2.0 or QC3.0 adapter. When connecting another
adapter, only the Wireless Charging function and the Alarm Clock can
be used in parallel.
Le manuel du propriétaire
FR
utilisation prévue
Ce produit est conçu pour être utilisé comme chargeur sans fil pour les
appareils compatibles Qi. Pour vérifier si votre appareil prend en charge la
norme Qi, lisez son manuel ou contactez le fabricant. Cet appareil est
destiné à un usage privé et non commercial uniquement. L'appareil ne doit
être utilisé que dans des environnements domestiques ou similaires.
L'appareil ne doit pas être utilisé dans des environnements avec une
atmosphère corrosive ou explosive ou à des fins médicales. L'appareil doit
uniquement être utilisé conformément à ces instructions d'utilisation. Toute
utilisation autre que celle décrite dans ce manuel est considérée comme
une utilisation non conforme. Les changements en cours de progrès
technique sont réservés.
spécifications:
Matériau du boîtier:
Plastique
Type de pile:
batterie au lithium-polymère
Tension d'entrée / courant:
5 V / 2,0 A
Tension / courant de sortie:
5 V / 1,1 A / 10 W
Dimensions:
environ 140 x 98 x 75 mm
Poids:
147 g
Note de sécurité:
● Lisez tous les avertissements de sécurité et toutes les instructions.
● S'il vous plaît prendre le temps de lire la sécurité générale. Pour la
sécurité générale dans une brochure séparée. Ce livret est inclus.
Déballer et vérifier le contenu:
● Lampe chargeur sans fil Lasse
● Type C USB <> USB A Branchez le câble
● Sécurité
Illustration du produit :
1.
heure d'affichage
2.
affichage des minutes
3.
veilleuse
4.
touche M
5.
Bouton "+" 5. bouton "+
6.
bouton "-".
7.
deux points supérieurs : Deuxième indicateur
8.
zone de charge sans fil
9.
Indicateur de charge sans fil
10.
Connexion d'entrée de type C
11.
touche veilleuse
12.
port USB de type A
Werbung
