Herunterladen Inhalt Inhalt Diese Seite drucken

HQ Power VL0612 Bedienungsanleitung

Vollautomatisches batterieladegerät für bleiakkus – (6v / 12v)
Inhaltsverzeichnis
Verfügbare Sprachen
  • DE

Verfügbare Sprachen

VL0612 / VL1212 – FULLY AUTOMATIC CHARGING SYSTEM FOR LEAD-ACID BATTERIES (6V / 12V)
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm
the environment.
Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialised
company for recycling.
This device should be returned to your distributor or to a local recycling service.
Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for buying the VL0612 / VL1212! Please read the manual thoroughly before bringing this device into service.
If the device was damaged in transit, don't install or use it and contact your dealer. This manual contains important
safety and operating instructions, please keep it for future reference.
2. Safety Instructions
WARNING: RISK OF EXPLOSIVE GASES. Working in the vicinity of a lead-acid battery is dangerous.
Batteries generate explosive gases during normal battery operation. For this reason, you should carefully
read and follow these instructions.
1. Keep away from children and unqualified persons.
2. To reduce the risk of battery explosion, follow these instructions and those marked on the battery carefully.
3. Never smoke or allow an open spark or flame in the vicinity of the battery or engine.
4. Do not expose the charger to rain or snow. For indoor use only.
5. The use of attachments not recommended or sold by the battery charger manufacturer may result in a risk of fire,
electric shock or personal injury.
6. To reduce the risk of damage to the electric plug and cord, pull the plug and not the cord when disconnecting the
charger.
7. Make sure the cord cannot be stepped on, tripped over or is not otherwise subjected to damage or stress.
8. Study all the battery manufacturer's specific precautions such as removing or not removing cell caps while
charging and recommended rates of charge.
9. Do not use the battery charger unless the battery voltage matches the output voltage rating of the charger.
10. Do not operate the charger in a closed-in area or in an area with restricted ventilation.
11. An extension cord should not be used unless absolutely necessary. The use of an improper extension cord could
result in a risk of fire and electric shock. If an extension cord must be used, make sure that:
a. the pins on the plug of the extension cord are the same number, size and shape as those of the charger plug.
b. the extension cord is properly wired and in good electrical condition.
c. the wire size is as specified in table 1 below. Do not operate the charger with damaged power core or plug.
d. The supply cord cannot be replaced. If the cord is damaged, the appliance should be discarded.
Cord length feet / metre
AWG cord size, table 1
12. To reduce the risk of electric shock, unplug the charger from the outlet before you start any maintenance or
cleaning activities.
13. Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer
will not accept responsibility for any ensuing defects or problems.
14. All modifications of the device are forbidden for safety reasons. Damage caused by such modifications is not
covered by the warranty.
VL0612/VL1212
25ft / 7.60m
50ft / 15.25m
18
1
100ft / 30.50m
18
18
150ft / 45.75m
18
VELLEMAN
Inhaltsverzeichnis
loading

Inhaltszusammenfassung für HQ Power VL0612

  • Seite 22: Especificaciones

    Falls Zweifel bestehen, wenden Sie sich für Entsorgungsrichtlinien an Ihre örtliche Behörde. Danke für den Kauf des VL0612 / VL1212! Überprüfen Sie, ob Transportschäden vorliegen. Sollte dies der Fall sein, verwenden Sie das Gerät nicht und wenden Sie sich an Ihren Händler. Lesen Sie diese Bedienungsanleitung vor Inbetriebnahme sorgfältig durch und bewahren Sie sie für künftige Einsichtnahme auf.
  • Seite 23: Persönliche Maßnahmen

    4. Vorbereitung 1. Wenn es nötig ist, die Batterie zum Aufladen aus dem Fahrzeug zu entfernen, entfernen Sie immer zuerst die geerdete Batterieklemme. Achten Sie darauf, dass alle Zubehörteile im Fahrzeug ausgeschaltet sind, um einen Lichtbogenüberschlag zu vermeiden. VL0612/VL1212 VELLEMAN...
  • Seite 24: Ladegerät Aufstellen

    Batterieklemme mit einem Hochleistungsstahl-Teil des Rahmens oder Motorblocks. 7. schließen Sie das Ladegerät mit dem mitgelieferten Stromkabel an eine Steckdose an. 8. zum Entfernen des Ladegerätes: trennen Sie das AC-Kabel, entfernen Sie die Klemme vom Fahrzeugchassis und entfernen Sie dann die Klemme vom Batterieanschluss. VL0612/VL1212 VELLEMAN...
  • Seite 25 (rot an positiv (+ an +) und schwarz an negativ (- an -)). Schalten Sie das Gerät nie ein und sofort wieder aus. Wenn das trotzdem doch geschieht, trennen Sie das Gerät vom Netz, warten Sie einige Minuten und schalten Sie es wieder ein. VL0612/VL1212 VELLEMAN...
  • Seite 26 Batterie bis zu 80% der Gesamtkapazität aufgeladen ist. Jetzt könnten Sie die Batterie wieder verwenden falls wirklich nötig. Es wird jedoch empfohlen, den Ladevorgang zu beenden. 4. Die grüne Kontrollleuchte brennt ununterbrochen: der Ladevorgang ist fertig und Sie können die Batterie wieder in Betrieb setzen. VL0612/VL1212 VELLEMAN...
  • Seite 27: Problemlösung

    Gerät wurde innerhalb von Sie 1 Minute und schließen Sie es Anfang des Ladevorgangs. einigen Sekunden ein- und wieder an. ausgeschaltet. 9. Technische Daten VL0612 6V / 1.25A Ausgangsleistung VL1212 12V / 1.25A Gewicht Abmessungen 93 x 82 x 105mm Länge Ausgangskabel 190cm Alle Änderungen vorbehalten.

Diese Anleitung auch für:

Vl1212

Inhaltsverzeichnis