Accessories and Spare Parts Please contact your nearest Salamander Designs dealer or www.salamanderdesigns.com/commercial Save these Instructions Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20]...
Seite 4
"L" shaped package inserts are reinforcing the box. Position the Header Wall as shown to allow assembly of Legs. the Header Wall as shown to allow assembly of the Legs. Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20] page 4 of 21...
Seite 5
Once both Legs are securely fastened to the Stand, use two people to lift the Stand to the upright position. I x 8 After legs have been securely fastened to stand, use two-people lift to stand to upright position. Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20] page 5 of 21...
Seite 6
Using four “H” Button Head Screws, attach two handles to the stand as shown below. Using four 1/4 - 20 x .5 Button Head Screws, attach the two Handles to the Stand as show. Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20] page 6 of 21...
Seite 7
display installation Attach Brackets to Display Check depth of screw threads in display before inserting screws. Inserting a screw that is longer than the hole could result in damage to display. Depth can be confirmed by inserting hex wrench into hole and marking its length then confirming this length is sufficient by comparing it to the screw you are using. Install interface mounting brackets (J) onto display as shown using supplied phillips screws (A-G) or screws specified by the display manufacturer. Hand tighten first to confirm thread and depth match. Note: Affix display brackets “Ears-Out” as shown Ears out...
Seite 8
Display height positions, install these two locating screws in the middle two holes in the Display Bracket. Use middle hole locations for two lowest display heights. Leave 1/4" of screw body exposed. Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20] page 8 of 21...
Seite 9
Using the straps “R” and or thumb screw / nut “N & O” attach your gear. Attach your gear using "M" straps and/or thumb screw and nut "J" and "K". Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20]...
Seite 10
LIMITED LIFETIME WARRANTY Salamander Designs Ltd. Limited Lifetime Warranty on Furniture and Seating products are guaranteed to be free from defects in design, material and workmanship, given normal use and proper care in a normal single shift Commercial environment, with the exceptions noted below. Salamander will repair or replace, at its discretion without charge to the original purchaser, any product or part thereof which fails as the result of such defects during the warranty period.
Seite 11
Thumb Nut Rack Gear Attachment Thumb Screw Rack Gear Attachment 400-010 Cable ties 301-720 301-715 301-700 301-735 3 400-125 Velcro cinch strap 1-700 301-735 302-281 300-485 Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20] page 11 of 21...
, o se ha dejado caer. Accesorios y Repuestos Por favor contacte su agente autorizado de Salamander Designs mas cercano o www.salamandercommercial.com Guarda estas instrucciones Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20]...
ATTENTION ! Lorsque vous déplacez l’appareil, utilisez la poignée pour déplacer et positionner l’appareil. Entretien • Nettoyez à l’aide d’un chiffon humide. Réparations • Confiez tout entretien à un personnel qualifié. Un entretien est nécessaire lorsque l’appareil a été endommagé de quelque manière que ce soit, tel que l’appareil a été exposé à la pluie ou à l’humidité, ne fonctionne pas normalement ou a été échappé. Accessoires et pièces de rechange Veuillez contacter votre commerçant de Salamander Designs le plus près ou www.salamandercommercial.com Enregistrer ces instructions Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20] page 13 of 21...
Weise beschädigt wurde, wie z.B. der Aussetzung von Regen oder Feuchtigkeit, sodass es nicht mehr normal betrieben werden kann. Zubehör und Ersatzteile Bitte kontaktiere Salamander Designs 860.761.9500 oderwww.salamandercommercial.com Speichern Sie diese Anleitung Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20] page 14 of 21...
Seite 15
Replace the box top. Remove Upper and Lower Rear Covers and position the Header Wall face up on the end of the closed box where the L shaped package inserts are reinforcing the box. Position Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20] page 15 of 21 the Header Wall as shown to allow assembly of Legs.
Seite 16
Une fois que les pieds ont été solidement fixés sur le support, demandez à deux personnes de soulever le support dans une position verticale. Nachdem die Beine gesichert wurden, hebe es in eine aufrechte Position. I x 8 Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20] page 16 of 21...
Seite 17
Nutze vier ”H” Halbrundschrauben und bringe wie angezeigt zwei Griffe am Stand an. Using four 1/4 - 20 x .5 Button Head Screws, attach the Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20] page 17 of 21 two Handles to the Stand as show.
Seite 18
INSTALACIÓN DE LA PANTALLA / INSTALLATION DE L’ÉCRAN / Anzeige installieren Ajuste los Soportes de la Pantalla Fixez les supports à l’écran Bringe die Halterungen am Display an Chequee la profundidad de la rosca de los tornillos en la pantalla antes de insertar los tornillos. Insertar un tornillo que es mas largo que el agujero puede resultar en un daño hacia la pantalla. La profundidad puede ser confirmada al insertar una llave hexagonal en el agujero y marcando su profundidad y luego confirmar esta longitud con el tornillo que esta utilizando.
Seite 19
Für die verbleibenden beiden unteren Höhenpositionen, bringe diese beiden Schrauben in den mittleren beiden Löchern der Displayklemme an. Use middle hole locations for two lowest display heights. Leave 1/4" of screw body exposed. Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20] page 19 of 21...
Seite 20
Attach your gear using "M" straps and/or thumb screw and nut "J" and "K". Mit den Riemen “R” und / oder Schraube / Mutter “N & O” befestigen Sie Ihre Ausrüstung. Salamander Designs - Fixed Height Mobile Display Stands 501-695 [4.20]...
Seite 21
LIMITED LIFETIME WARRANTY Salamander Designs Ltd. Limited Lifetime Warranty on Furniture and Seating products are guaranteed to be free from defects in design, material and workmanship, given normal use and proper care in a normal single shift Commercial environment, with the exceptions noted below. Salamander will repair or replace, at its discretion without charge to the original purchaser, any product or part thereof which fails as the result of such defects during the warranty period.