Before Assembly - Palram Palermo 3000 Montageanleitung

_A
r
L
IMPORTANT
Please read
these instructions carefully before you start to assemble this product.
Please
carry
out the
steps
in
the order set out
in
these instructions.
Keep these
instructions
in
a
safe place
for future
reference.
Safety advicc
For
safety purposes we strongly recommend the product to
be
assembled by at
least two people.
Some parts may have sharp edges. Please be careful when handling components.
Always wear gloves, eye
protection, and long sleeves when assembling or
performing
any maintenance on your product.
Do
not attempt to assemble the product
in
windy
or
wet conditions.
Do
not attempt to
assemble the product if you
are
tired,
have
taken drugs,
medications
or alcohol, or
if
you are
prone to dizzy
spells.
Dispose
of
all
plastic bags safely
-
keep them away from children's
reach.
Keep
children away from the assembly
area.
When using
a
stepladder or power tools, make sure
that
you are
following
the
manufacturer's safety advice.
Do
not climb or stand on the roof.
Do
not hang or
lay on
the profiles.
Heavy articles should not
be
leaned against the poles.
Keep
roof
and
gutters
clear
of
snow,
dirt
& leaves.
Heavy snow load on
the roof
can
make it unsafe to stand below or nearby.
If color was scratched
during
assembly it can be fixed.
Cleaning instruction:.
In
order to clean the product,
use
a
mild detergent solution and rinse
with
cold clean water.
Do not
use
acetone, abrasive cleaners, or other special detergents to clean the
panels.
Clean the product once assembly
is
complete.
Before Assembly
Choose your site carefully before beginning assembly.
The
ground
surface must be
perfectly flat and leveled and
have
a
solid base such
as
concrete, asphalt, deck
etc.
Sort the parts and check against the
content
parts list.
Parts
should be laid out close at hand. Keep all small parts (screws etc.)
in
a
bowl
so
they do not get
lost.
Please
consult your
local
authorities if any permits
are
required prior to
constructing the product.
If you wish to add Palram's doors / walls closure to your gazebo, please carry
out the
steps in
the order
set
out
in
the
Ledro Enclosed Gazebo
instructions.
Should you do
so,
some parts
will
be surplus.
Attention
Please
make sure you install the
panels
with the
UV
protected
side
out
(marked
with
"THIS SIDE
OUT") and remove the sticker
as
panels
are in
place.
During Assembly
When encountering the information icon, please refer to the relevant
assembly step for additional comments and assistance.
During assembly
use
a
soft surface below the parts to avoid scratches
and damages.
Steps
Steps 3-12:
It
is
recommended to
use
a
carton or other soft material under the
lowered corner
in
order to avoid scratches and peeling of paint.
Step 10: Optional
-
if you wish to add
Palram's
Curtains or Netting
Set, please
thread the plastic clips through the
rail in each
profile.
(Palram's Curtains
/
Netting
Set are
not supplied).
Steps
11
a+13a:
Please
note
that threading of
the screws should
be
done from
the outside
Steps 12+14:
Please
note that threading of the
screws
should
be
made from
the bottom
up.
Step 15a:
Please
add silicone
on
the inner
area
of part #8327
as
illustrated
Step 21a:
Please
drill holes
in
the panels to
be
located precisely parallel to
the holes
in
profile #9249.
Step 22:
Please level the profile's legs and adapt screws and plugs to your specific
ground type.
* Please
tighten
all screws when completing assembly.
Do
not tighten
screws and nuts (8192 & 466)
until completion of assembly
process. These
2
icons
indicate if screws'tightening
is
required or not.
A
Di
1
[
:
466
2
]
Note:
Anchoring this product to the ground
is
essential to its
stability
and
rigidity.
It
is
required to complete this
stage in
order for your warranty to
be
valid.