HIK VISION DS-PD2-T10P-WEH Montageanleitung

DS-PD2-T10P-WEH/WEH1
E N G L I S H
Diagram References
1
PCB Overview
2
LED Indications
3
Microwave Adjustment:0m to 15m
4 Dip Switched 1-4
5
Registration
Please register the device within 90 seconds after it being powered on.
Register Locally
1. Make the security control panel enter the registration mode.
2. Register the detector: Hold the registration key until the three LEDs flash
alternately. The green LED will flash 8 times if the registration is finished.
3. Communication Test: Release the TEMPER spring to trigger the alarm.
Note: The distance between the security control panel and the detector
should be less than 50 cm.
Initialize the Detector
1. Remove the battery to power the detector off.
2. 5s later, hold the registration key and reinstall the battery to power the
detector on at the same time to make the three LEDs start flashing alternately.
Release the registration key while the three LEDs flash once together.
Register Via APP
1. Log in to the APP Store and input "Hik-Connect" to search the mobile client.
Download and install Hik-Connect to your phone.
2. After installing, tap to run the client.
3. Power on the security control panel.
4. Log in the Hik-Connect and tap the icon "+" at the upper-right coner of the
Hik-Connect page to add the security control panel. You can scan the QR code
on the device rear panel or on the package box, or on the package box, or
input the device serial No. manually to add the device when the device is in
the registration mode.
5. After adding the security control panel, tap the arming status icon on the
right of the security control panel's name to enter the Partition page.
6. Tap the "+" icon on Partition page to add the peripherals.
6 Signal Strength Test
Inserting the Fixed Mask or Flexible Mask
7
8
Flexible Mask Adjustment(1)
9
Flexible Mask Adjustment(2)
10
10m Lens Diagram
11
Wall Mounting Bracket ＆ Adapter
12 Wall Mounting Bracket
13
Fixed Bracket
14
Guidelines
Technical Specification
Detectors Technical Characteristics
Detection Range 10m
Detection Angle 90°
Detection Zones 78 zones and 5 planes
Detection Speed 0.25–3m/s
Mounting Height 1.8-2.4m
Two-way Wireless Technology Yes
Blue Wave Technology Yes
Dual Element Pyroelectric Sensor Yes
Tamper Protection Front, rear, and bracket tamper signal input
Intergrated Walk Test Buzzer Yes
Top: Microwave, PIR 1 and alarm
Separated LED Indication
Bottom: PIR 2
Signal Strength Indicators (SSI) Yes
3 Microwave Frequencies to Avoid Interference Yes
Digital Independent Floating Threshold(IFT) Technology Yes
Plastic Housing Polycarbonate
Animal Immunity
10kg
Optics
Sealed
High or low range
Adjustable Sensitivity
0.4mm HDPE in lens area
Lens UV compensated
Detection Method Tri-Signal Detection Logic
Sensor 2 low noise dual element passive infrared sensors and a microwave doppler unit
Environmental and Operating Features
Weatherproof IP55 rated
Certified Operating Temperature -25℃ ~ +60℃(Certified)
Physical Dimensions(H x W x D) 180mm x 80mm x 105mm
Weight 500g
Electrical & battery
Transmission Frequency 433MHz, FM transceiver
Range in Open Space 800m
Battery Type 2x3V Lithium battery (included)
Accessories
Rotatable Wall Mounted Yes – additional wall and fixed brackets available separately
Fixed Wall Mounted Yes – additional wall and fixed brackets available separately
Ceiling Mounted Yes – additional wall and fixed brackets available separately
Battery Additional Battery available separately
Battery Information
The batteries supplied have been chosen to provide long service life whilst,
for safety reasons, having limited output current.
The battery leads must be connected for operation. When disposing of the
product, the battery must be removed and disposed of separately in
accordance with the local regulations.
1
UD15577B
3
4
3
11 12 13
11 12
4
2
5