Herunterladen Inhalt Inhalt Diese Seite drucken

Esco BBH-40 Bedienungsanleitung

Reifenwulstabdrücker
Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 7
L2190
Rev. O
IMPORTANT RECEIVING INFORMATION
Visually inspect all parts for shipping damage. If you find shipping damage, notify the carrier at
once. Shipping damage is not covered by your warranty. The carrier is responsible for all costs of
replacement or repair caused by shipping damage.
CONTENTS
ENGLISH...........................................1-6
DEUTSCH .......................................7-12
DESCRIPTION
The BBH-40 Bead Breaker is used on all types of rims except 5-piece earthmover rims. It is ideal
for use with truck, farm tractor, grader, combine, and skidder tires. The BBH-40 can be used with a
model AHP15T (10500), AHP25TP (10502), AHP35T (10504), or equivalent 10,000 psi [700 bar]
pump.
SAFETY INFORMATION
To avoid personal injury or property damage while using this product, read and follow all
DANGERS, WARNINGS, CAUTIONS, and INSTRUCTIONS that are attached to, or included
with, this product.
1. Follow the instructions of the tire manufacturer and the vehicle manufacturer when deflating,
demounting, mounting, and inflating tires.
2. These operating instructions do not apply to any specific rim. Therefore, contact the rim
manufacturer for the correct procedure for your rim.
3. For the publication, "Multipiece Rim Matching Chart" contact the United States Department
of Labor, Occupational Safety, and Health Administration (OSHA), Washington, DC, 20210,
202-219-6091, or contact ESCO at 1-800-352-9852. If you are outside the U.S., contact your
local government officials.
4. ESCO cannot be held responsible for damage or injury resulting from unsafe use of this
product; lack of maintenance; or incorrect product and system application.
5. Contact ESCO when in doubt about safety precautions or applications.
The bead breaker, and all tire tools, should be used only by persons properly trained according
to OSHA Regulation #29CFR1910.177, "Servicing Single-Piece & Multi-Piece Wheels." Free copies
of this regulation are available upon request from ESCO.
A WARNING
To avoid serious personal injury, always wear proper protective gear, such as hard hats, safety
glasses, gloves, and steel toe shoes when using hydraulic equipment.
10/97
FRANÇAIS ................13-18
ESPAÑOL ..................19-24
A CAUTION
Instruction Sheet
10101 Tire Bead Breaker
ITALIANO ..............25-30
NEDERLANDS ......31-36
Inhaltsverzeichnis
loading

Inhaltszusammenfassung für Esco BBH-40

  • Seite 6 - 6 -...
  • Seite 7: Wichtige Anweisungen Für Die Eingangskontrolle

    Reparaturkosten, die sich aus einer Beschädigung beim Transport ergeben. BESCHREIBUNG Der Wulstabdrücker BBH-40 kann an allen Felgentypen verwendet werden, außer an fünfteiligen Felgen von Erdbewegungsmaschinen. Er eignet sich in idealer Weise für Reifen von Lastwagen, Ackerschleppern, Gradern, Mähdreschern und Skiddern. Der BBH-40 kann in Verbindung mit den Modellen AHP15T (10500), AHP25TP (10502), AHP35T (10504) oder einer gleichwertigen 700 bar [10,000 psi]-Pumpe verwendet werden.
  • Seite 8 Abbildung 1 Abbildung 2 Abbildung 3 Abbildung 4 - 8 -...
  • Seite 9: Aufziehen Und Aufpumpen

    HINWEIS: Möglicherweise sind mehrere Versuche nötig, bis das Felgenhorn gleichmäßig erfaßt wird. Beim Erfassen des Reifenhorns den Wulstabdrücker nicht mit grober Kraft anlegen. 2. Den Hydraulikdruck weiterhin steigern, bis der wulstabdrückende Kolben etwa 6,35 mm [1/4 in.] aus dem Wulstabdrücker ausgefahren ist. (Siehe Abb. 4.) 3.
  • Seite 10 Bedienungsperson außerhalb der Fluglinie eines berstenden Reifens steht. Die Druckluftleitung muß mit einem In-Line-Ventil mit einem Druckmesser oder einem voreinstellbaren Druckregler ausgestattet sein. Verwenden Sie die ESCO-Lkw-Reifenpumpe, Modell 15136. A GEFAHR Verwenden Sie zum Aufpumpen eines Reifens stets einen Sicherheitskäfig oder eine Schutzvorrichtung.
  • Seite 11 2. Den Reifen auf 0,345 bar [5 psi] aufpumpen. 3. Alle Reifen- und Felgenteile nochmals auf richtige Anordnung prüfen. 4. Wenn die Reifen-/Felgenteile nicht richtig sitzen, die Luft aus dem Reifen ablassen und das Problem beheben, bevor mit der Arbeit fortgefahren wird. A ACHTUNG Hämmern, schlagen oder pressen Sie niemals an einer aufgepumpten oder teilweise aufgepumpten Reifen/Felgen-Einheit.

Diese Anleitung auch für:

10101

Inhaltsverzeichnis