Herunterladen
Teilen
Diese Seite drucken
  1. Anleitungen
  2. Marken
  3. Thermon Anleitungen
  4. Steuergeräte
  5. Terminator ZT-P-XP
  6. Installationsanweisung

Thermon Terminator ZT-P-XP Installationsanweisung

Thermostat connection kit
Vorschau ausblenden
1
2
3
4
5
6
7
8

Werbung

Quicklinks

Diese Anleitung herunterladen
TM
Terminator
ZT-P-XP
Thermostat Connection Kit
INSTALLATION PROCEDURES
For Thermostat Connection (1-2 Heating Cables) Applications
For Use With Parallel Heating Cables
The Heat Tracing Specialists
®

Werbung

loading

Verwandte Anleitungen für Thermon Terminator ZT-P-XP

Inhaltszusammenfassung für Thermon Terminator ZT-P-XP

  • Seite 1 Terminator ZT-P-XP Thermostat Connection Kit INSTALLATION PROCEDURES For Thermostat Connection (1-2 Heating Cables) Applications For Use With Parallel Heating Cables The Heat Tracing Specialists ®...

  • Seite 2: Installation Procedures

    INSTALLATION PROCEDURES Receiving, Storing and Handling . . . The following installation procedures are suggested guidelines for the installation of the Terminator ZT-P-XP Kit. 1. Inspect materials for damage incurred during shipping. Kit Contents . . . 2. Report damages to the carrier for settlement.
  • Seite 3 Terminator ZT-P-XP INSTALLATION PROCEDURES GRW-G/Tstat Locate bus connection (HPT and FP only) For HPT and FP cable, exchange grommet Insert cable into expediter. If mounted on and cable as shown. Cut end of cable at in Terminator with grommet provided in bottom or side of pipe, punch out weep hole.
  • Seite 4 Terminator ZT-P-XP INSTALLATION PROCEDURES Route thermostat bulb through nut Fix thermostat bulb and capillary tube to Mount expediter to pipe using pipe band. and expeditor opening in junction box Do not band over cable. Tape cable pipe. base. If necessary, apply lubricant (user expansion loop to pipe.

  • Seite 5: Wiring Details

    Terminator ZT-P-XP INSTALLATION PROCEDURES Two Cable Layout Tips Locate bus connection (HPT and FP only) and Insert two cables into expediter. cable as shown. Cut end of cable at angle to Note: For HPT and FP cable, exchange aid in piercing grommet. Leave additional cable grommet in Terminator with grommet provided for expansion loop.
  • Seite 6 (disjoncteur différentiel). Reportez-vous aux instructions d'installation des PETK. Repousser • L'installation doit se conformer aux exigences Thermon (y compris la l'excédent de câble en arrière à travers l'EXPEDITER. Faire avec notice PN 50207U pour les installations Ex) et doit être réalisée en ce câble, une lyre d'expansion sur le tuyau.

  • Seite 7: Инструкция По Монтажу

    9. Retire el Expediter de la tubería soltando la banda de fi jación. • La instalación debe cumplir con los requisitos de Thermon 10. Guíe el bulbo del termostato a través de la base de la caja del (incluyendo el estándar PN 50207U para sistemas Ex) y debe...
  • Seite 8 • Thermon verwarmingssystemen moeten altijd geïnstalleerd worden 8. Gebruik de installatie instrukties van de desbetreffende PETK- met de correcte elektrische beveiligingen. Thermon adviseert altijd set voor het maken van een voedingaansluiting of eindafsluiting een installatie automaat/zekering met aardlekbeveiliging toe te van de verwarmingskabel.