kellermann BL 1000 LED Anbauanleitung Seite 2

Installation instructions BL 1000 LED/ Dark / BL 2000
Frontal directional indicator
Dear customer,
Thank you for placing your trust in us by purchasing this product. Please read these installations instructions carefully and completely before
deciding whether you would like to do the installation yourself or have it done by a specialist. If you have any questions or concerns, or if you
need replacement parts, send us an e-mail (info@kellermann-online.com) or call us (+49 (0)241/ 9 38 08-0). We are happy to help.
OVERVIEW OF COMPONENTS
1. BL1000 LED/Dark/BL 2000
2. Rubber ring
3. Sliding disc (washer)
4. Mounting rubber
5. Nut
6. Adapter set 1, for handlebars with small internal diameters
7. Adapter set 2, for handlebars with a large internal diameter
(inch handlebar)
8. Two cord connectors (not shown)
Mounting rubber
BL 1000 LED/Dark
Rubber ring
LEGAL AND OTHER INFORMATION
The BL1000 LED/Dark/BL 2000 is, in accordance with installation specifications, ECE-approved as a frontal directional indicator for motor-
bikes that are approved according to European law. This is documented by the approval numbers stamped into the light covers. For you, this
means that you can use two BL1000 LED/ Dark/ BL 2000 units instead of your original indicator lights without registering anything in your
vehicle documents and without taking your vehicle to a technical inspection service. You do not need to carry any special documentation.
If you would like suitable rear directional indicators, we would like to recommend the micro 1000 series. You can choose from among over
twenty variations.
ATTENTION! Correct mounting and electrical connection are requirements for the guarantee. For this reason, only do the installation yourself
if you are properly trained. Otherwise, go to a specialist and let him or her install and connect the BL1000 LED/Dark/BL 2000. Damages
resulting from excess voltage (e.g. as a result of a defective alternator controller) does not constitute a valid claim.
ATTENTION! Insufficient fastening or incorrect alignment of the BL 1000 LED / Dark /BL 2000 can lead to a revocation of your operating license
and of your vehicle insurance, and to accidents. Before every usage of your vehicle, check whether the indicators are correctly mounted and
fully functional.
ATTENTION! The BL 1000 LED / Dark / BL 2000 may become heated in operation. Contact with unprotected skin or heat-sensitive objects
may lead to averse effects.
CLEANING ADVICE! Your new Kellermann products are premium-quality products. In order to enjoy them long time and maintain the
warranty we recommend not to use any cleansers with alkaline/acid and/or grinding substances or steel wool. We also advice not to
use steam cleaners.
ATTENTION! Before installation, it must be determined that the motorbike is in a safe position, because if it falls it could cause injury or
damage to the motorbike.
1. The BL 1000 LED / Dark/ BL 2000 Dark / Chrome can be mounted onto handlebars that are hollow and at an imagined perpendicular
transversal plane have an angle of 9 - 25° (BL 1000 LED/ Dark) or 12-18° (BL 2000) to the rear. De-install the original indicator lights and the
original handlebar covers or handlebar vibration dampers so that the hollow handlebar ends can receive the BL 1000 LED/ Dark / BL 2000.
2. The cords of the BL 1000 LED/Dark / BL 2000 run inside the handlebar and must be drawn through to an appropriate position. For this pur-
pose, drill a hole if needed into the handlebar and assure a smooth passage of the cord without sharp edges.
3. Select the largest of the four mounting rubbers that will fit into the end of the handlebar and position the fitting rubber rings and nuts.
Position the rubber ring at the point between the indicator light and the screw thread. For handlebars with small internal diameters, the BL 1000
LED /Dark /BL 2000 is to be installed without a rubber ring.
Page 1
Adapter set 1, Adapter set 2,
for handlebars with small for handlebars with a large internal
internal diameters
diameter (inch handlebar)
Nut Mounting rubber
BL 2000
Sliding disc
Rubber ring
(washer)
INSTALLATION
english
4. First position the sliding disc (washer) and then the mounting rubber onto the indicator's screw thread and screw on the nut.
5. Hold the indicator tight with one hand and screw the nut with a suitable tool until the mounting rubber is only lightly clamped when it is
inserted into the handlebar.
7. Note the position of the BL 1000 LED/Dark/BL 2000 and screw it in a clockwise direction. The indicator should cast its light forwards and
parallel to the ground. If it does not do so, loosen the indicator, pull it out and put it back in at an angle that will align it correctly once it is
screwed in. Repeat thisuntil the direction of the light is correctly aligned. Fine alignment is described under point 9.
8. Electrical connection: Divide the feed cables between the original frontal indicator light and your connector in a suitable position. Connect
the BL 1000 LED/Dark /BL 2000 as follows:
· Connect the positive side of the left (right) indicator with the grey cord of the left (right) BL 1000 LED/ Dark/ BL 2000
· Connect the negative side of the left (right) indicator with the black cord of the left (right) indicator.
The BL 1000 LED/Dark /BL 2000 includes cord connectors that are to be used as follows: Remove the isolation from the ends of the cords at a
length of ca. 1 cm and position the cords that are to be connected in one of the provided end connector sleeves. Then press it tightly together
with suitable pliers (see Fig. 1-3). This kind of cord connector is, in a technical sense, not removable. In order to connect the cord in a removable way,
we recommend Posilock cord connectors. You can order these on the website www.kellermann-online.com, among other places.
Position the cords and fasten them in an appropriate manner, e.g. with cord connectors. Test the functionality of the BL 1000 LED/Dark/ BL
2000 on your vehicle.
9. The proper alignment is necessary for safety when driving in traffic and a required component for vehicle approval; a vehicle with incorrectly
Nut
aligned lights is easily not noticed.
Sliding disc
(washer)
The flashing frequency can change when converting the original indicators. The installation of a load-independent flasher relay (e.g. R2) or a
multifunctional assistance system (e.g. CR 4®) will solve the problem. If the installation is not possible or not favored, then parallel connected
power resistors (i.LOAD) will be an option. Only a few vehicles need special solutions, which we offer as i.SED, i.BOS products.
ATTENTION! These resistors will heat up if the indicator is used for an extended period. Make sure that other components are safe.
We are happy to answer any questions you may have with regards to converting your indicators, we are certain we can help you.
Our team is constantly working on new, improved solutions for all models and vehicles. If you are not sure which electronic equipment you
require, please contact us via www.kellermann-online.com
ATTENTION! The application of the described measure may interrupt correct functionality, in the case of a failure causing one of the
indicator lights to increase in flash frequency in order to alert the driver of such a failure. Before each usage of the vehicle, check the
functionality of the indicator lights.
The Kellermann Atto®/Atto® Dark is equipped with the tried-and-trusted Longlife Protection Guard® circuit, which ensures extremely
long life with LED technology. It is not necessary to replace the illuminant and, due to the UNECE regulations, it would not be allowed either.
On our homepage, www.kellermann-online.com, you will find our online shop with our extensive assortment of replacement parts and
accessories in the downloads field.
Online shop at www.kellermann-online.com
6. Draw the cord through the handlebar (it can be helpful to use a wire loop to pull it through). As far
as possible, the cord should not be loose inside the handlebar once the BL 1000 LED/ Dark /BL 2000 is
installed.
Toward this end, turn the indicator a few times counter-clockwise before you insert it into the handlebar.
In order to align the indicators, position the motorbike at a right angle to a light-colored wall. Sit
on the motorbike and measure the height of the middle of the indicator glass above the (flat)
floor). Make a mark on the wall at this height. This mark on the wall must be exactly in the middle
of the indicator's light field. If necessary, adjust the indicator as described in point 7.
This completes the installation process.
INDICATOR FLASH RATE
or call us: +49 (0)241/93 80 8-0.
BL 1000 LED
Page 2 english
BL 1000 Dark BL 2000