CTR-51 1-Channel
LED Flash Controller
Bedienungsanleitung des 1-Kanal CTR-51 LED
Blitzcontrollers
1. Warn- und Anwendungshinweise
Bitte vor Verwendung des Gerätes die Warn- und
Anwendungshinweise sorgfältig durchlesen.
Allgemein - Das Gerät ist für nur die Verwendung in
Innenräumen ausgelegt.
Gesundheit - Bei Installations- und Wartungsarbeiten ist
das Gerät vorher von der Stromversorgung zu trennen. Das
Gerät darf nicht verwendet werden, wenn ein Ausfall zu
einem Personenschaden führen kann.
Hitze - Bei sehr hohen Blitzströmen und einem hohen
Auslastungsgrad können Temperaturen an den Kühlrippen
größer 60° C auftreten. Es ist auf ausreichendem Abstand zu
leicht entflammbaren Materialien zu achten.
Elektrischer Anschluss - Das Gehäuse ist von der Masse
der Spannungsversorgung elektrisch isoliert. Ein
Überschreiten der zulässigen Betriebsspannung Uin oder
des zulässigen Schaltstromes pro Kanal kann zur Zerstörung
des Gerätes oder zu einer erheblichen Verkürzung der
Lebensdauer der angeschlossenen LED-Beleuchtung führen.
Mechanischer Einbau – Der Controller ist für die Hut-
schienenmontage vorgesehen. Ein Clip dient zur
Verriegelung an der Hutschiene. Für eine optimale Wärme-
abgabe ist links und rechts zum nächsten Gerät ein
Mindestabstand von 10mm einzuhalten.
2. Leistungsmerkmale
1-Kanal Blitzbetrieb
•
Hochpräzise Blitzpulse von 1µs bis 1500µs
•
Intelligente Ansteuerung der MBJ Beleuchtung via
•
Rsense-Technologie
Ansteuerung von Fremd-LED-Beleuchtungen
•
Einfache Konfiguration von LED Blitzlänge – und Strom
•
über Drehschalter.
Passive Kühlung.
•
Kamera mit I/O-Funktionen direkt anschließbar
•
Integrierte 24VDC Kameraspannungsversorgung
•
Fernsteuerung und Konfiguration über RS232 I/F
•
3. Elektrische Anschlüsse
MBJ Imaging GmbH
support@mbj-imaging.com
Neuer Höltigbaum 15
www.mbj-imaging.com
DE 22143 Hamburg
Tel.: +49 40 226 1623 30
Operating manual of the 1-channel CTR-51 LED flash
controller
1. Cautions and instructions for use
Please read the warning and application instructions carefully
before using the backlight.
General - The device is designed for indoor use only.
Health – The device must be disconnected from the power
source before the installation and/or maintenance can start.
The device must not be used when a failure may cause a
personal injury.
Heat - In case of running the device with a very high flash
current is a high duty cycle the heat sink temperature may
exceed 60 ° C. Keep off flammable materials at any time.
Electricity - The housing is electrically isolated from the
ground of the power supply. Exceeding the permissible
operating voltage Uin or exceeding the maximum allowed
switched current per channel can lead to the destruction of
the device or to a significant shortening of the lifetime of the
connected LED lighting module.
Mechanical integration – The controller is made for top hat
rail mounting. A clip can be used to lock the unit to the top
hat rail. For optimal heat flow a left/right distance of 10 mm to
next unit is mandatory.
2. Key specification
1-channel operation for flash light usage.
•
Very precise flash pulses from 1µs to 1500µs
•
Intelligent MBJ lighting control via Rsense technology
•
with detection of LED current
Support for 3d party LED lightings
•
Easy set-up of LED flash length and current via rotary
•
switches
Passive cooling.
•
Interface for direct camera connection.
•
Integrated 24DC power supply for MV camera
•
Set-up and configuration via RS232 remote control
•
3. Electrical connection
CTR-51
Release: 1.01
07.08.2018