Intermec 1015CP01 Anleitung Seite 2

U.S.A. Digital Emissions Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that can cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the radio or television receiving antenna.
• Increase the separation between the computer equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
• Consult the dealer or an experienced radio television technician for help.
Canadian Digital Apparatus Compliance
This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that can cause undesired
operation.
CAN ICES-3 (B)/NMB-3 (B)
802.11a Radio Precaution Statement
• 802.11a wireless LAN 5150 to 5250 MHz (5.15 to 5.25 GHz) (5 GHZ radio channels 34 - 48) is restricted to indoor operations to reduce
harmful interference to co-channel Mobile Satellite System (MSS) operations.
• The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit.
• The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-
point and non point-to-point operation as appropriate.
• Be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5470-5725 MHz and
that these radars could cause interference and/or damage to LE-LAN devices.
For Users in Europe
Imager and Camera Flash Compliance and Precaution
This product complies with the following standards for laser and LED safety:
• IEC 60825-1:2007/EN 60825-1:2008-05: Class 2 (1 mW, 630-680 nm)
• IEC 60825-1/EN 60825-1: Class 1 LED Product (imaging options only, no laser label)
• IEC 62471:2006-07 for LED safety
This product may use any of the following Intermec scan engines:
• EA30
• EA31
To find Laser and Imager classification information for Intermec scan engines, go to www.intermec.com > Products > Computers >
Handheld Computers > CN51 > Manuals tab, and then scroll down to Regulatory Information.
The camera assembly with flash is classified as: Risk Category 2.
Caution: When using the camera flash, keep the camera flash LED at least 317 mm (12.5 in) away from the subject's eyes. Otherwise
serious damage to one's eyes may occur.
If applicable, this product will be provided with a set of laser safety labels illustrated on the last page(s) of this document. If the proper label
language is not installed on the device, locate and apply the appropriate label over the existing label.
Caution: 802.11a wireless LAN 5150 to 5350 MHz (5.15 to 5.35 GHz) is limited to indoor use only.
Note: Dynamic Frequency Selection and Transmit Power Control are required in the 5250 to 5350 MHz and 5470 to 5725 MHz frequency
range.
EU - R&TTE Declaration
Intermec Technologies Corporation declares that this device is in compliance with the essential requirements and other relevant provisions of
R&TTE Directive (1999/5/EC). To find the EU Declaration of Conformity, go to www.intermec.com > Products > Computers > Handheld
Computers > CN51 > Manuals tab and then scroll down to Regulatory Information.
This product is marked with this logo and uses radio frequency bands that are harmonized throughout the
0981
European Community.
This equipment may be operated in the following countries without restriction:
AT BE CY CZ
MT NL PL PT
AL BA
2
DK EE FI FR
SK SI ES SE
GE HR MD MK
DE GR HU IE
GB IS LI
ME RS UA
IT LV LT LU
CH BG RO TR