V2 WES-ADI Bedienungsanleitung Seite 12

CONFIGURING THE CONTROL UNIT AND THE BASE UNIT
The control unit into which the WES-ADI device is inserted should be configured in order to be able to process the information sent from
this device. Please refer to the control unit manual in order to perform the device recognition procedure.
If the control unit has a display menu, then it is possible to configure the WES-ADI operating mode by using the control unit programming
keys and display; otherwise, the WES-ADI device should be used in its default configuration, and it is only possible to modify the
communication channel.
CONFIGURING THE BASE UNIT USING THE DISPLAY
In the control unit menu, when ADI device recognition is enabled, the display shows the identity of the device connected, in this case: WES.
Pressing the DOWN key opens the network configuration menu nEt; press the MENU/OK key to enable the WES module.
The display shows the number of the radio channel currently selected; if the network has still not been created, it is possible to change the
radio channel and the right hand side of the display shows the relative quality of the channel selected (one, two or three bars); once the
network has been created it is no longer possible to change the radio channel and the display shows a dot.
Pressing the MENU/OK key once more displays the number of sensors connected to the network (if the network has not yet been created
it shows nS00 ). This value is for information only and cannot be changed; press the MENU/OK key to return to nEt.
Pressing the DOWN key accesses the base unit output association menu (out); outputs is understood to refer to the alarm status of the
two units to which the sensors may be connected and signalling low device battery status.
Pressing the MENU/OK key accesses the Group 1 (GrP1 ) output configuration menu; press MENU/OK once more to display the type of
safety device associated with the unit:
CoSt : a safety device that signals a collision with an obstacle, such as a sensitive edge;
•
Foto : a safety device that signals the presence of an obstacle in the gate path, such as a photocell;
•
no : no safety device associated with this group
•
Select the desired type of safety device, using the UP and DOWN keys, and confirm using MENU/OK; it is then necessary to further specify
how the safety device should intervene:
CoSt safety devices:
Ch : during closure only, if activated, it forces the gate to move back for 2 seconds and then blocks it (automatic closure disabled);
•
Ch.St : behaviour during closure is as above, in other cases the gate is immediately blocked;
•
AP : as with the first case, but intervention is only during opening;
•
AP.St : as above, in other cases the gate is immediately blocked.
•
Foto safety devices:
Ch : During closure, it causes the gate to be completely reopened, during a pause it starts the automatic closure countdown;
•
in other cases, nothing happens;
Ch.CF : as above, and it also prevents an opening cycle from starting, if activated when the gate is stopped;
•
AP.Ch : as above, and it also stops the gate during opening until the safety device is deactivated.
•
Confirm the selection using the MENU/OK key and return to GrP1 .
Pressing the DOWN key switches to Group 2 (GrP2 ), and the same procedure is used to associate the desired safety device.
Once in GrP2, press DOWN once more to set the low battery alarm (L.bAt);
enter the programming options by pressing MENU/OK and select from the available options:
no : no signalling
•
LUCi : in the case of a low battery, when the courtesy light connected to the gate is turned on, three flashes are emitted;
•
FLSh : during the cycle, the flasher unit emits dual flashes;
•
LU.FL : both types of signals ere emitted.
•
Confirm the selection using the MENU/OK key and press the DOWN key to return to out.
Press the DOWN key once more: the display shows SAvE .
Press the MENU/OK key to save the settings and return to the control unit configuration menu.
Should you wish to exit without saving, press the DOWN key once more (display shows ESC) and confirm with MENU/OK.
PLEASE NOTE: The channel cannot be modified after the network has been configured.
12