Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Curtarolo (Padova) Italy
www.avselectronics.com
BIP 2 & BIP 2 Plus
Rolling code technology remote control. It can be used as a key ring. Allows up to
8 functions, embedded multi-color LEDs offer simple feedback on the commands performed.
TECHNICAL DATA
BIP 2 Plus bidirectional compatibility
Operating frequency
Functions
3V Lithium Battery
Consumption in transmission
Consumption in reception
Maximum range
Temperature
Dimension in mm (l x h x p)
Housing
Remote control Addressing (1 to 16):
1. Press together buttons 1 and 5 (all LED should be off), hold them until the flashing simultaneously the green led (A) and red
led (C)
2. Release the buttons 1 and 5, the green LED will indicate the tens of the address (0 = tens, 1 flash = 1 ten)
3. Each press of the button one, the tens increase by 1, eachpress of the button 3 the tens decrease of 1.
4. When you reach the desired value, press the button 5 to switch to the units.
5. The red LED will indicate the units of the address (off = unit , 1 flash = 1 unit, 2 flashes = 2 units, etc ..., 9 flashes)
6. Each time you press of the button 2 units will increase by 1, each time you press the button 4 units decrease by 1.
7. When you reach the desired value, press 5 to exit programming
Remote Control Learning:
Refer to the control panel manual, where it needs to be learned.
Control panel settings for activation system feedback , combined with XSAT WS (recommended for single sector):
1. The step "Programming OC" select the OC output corresponding to the XSATWS satellite Virtual Output No. 2.
(Ex: If the satellite has the address No. 1, the control panel OC output to be programmed will be the 10)
2. Program O.C. as category "Arming" and set all kinds of Arming to YES and disarming to NO.
3. Select the reference "Sector"
4. Set the OC arming time as "Bistable"
Control panel settings for activation system feedback , combined with XSAT WS (recommended for multi sector):
1. In the step "Programming OC" select the OC, corresponding to the XSATWS virtual output No. 3
(Ex: If the satellite has the address No. 1, the output OC will be programmed in the central 11)
2. Program O.C. as category "arming" and set all kinds of arming to YES and disarming to NO.
3. Select the reference "Sector"
4. Set the OC activation time to "3 seconds"
5. In step "OC Programming " select the OC corresponding to the XSATWS Virtual Exit No. 4
(Ex: If the satellite has the address No. 1, the OC output to be programmed in the control panel will be the 12)
6. Program the O.C. as category "Arming" and set all kinds of arming to NO and the disarming to YES ..
7. Select the reference"Sectors"
8. Program the OC activation time to "3 seconds "
Product mentioned in this statement is conform to basic indications of directive 1999/5/CE (R&TTE) on low-power radio-transmitting devices and on use of frequen-
cies of the radio-electrical spectrum, in accordance with CEPT 70-03.
Danger of explosion if battery is not replaced in a correct way. Replacement must be made using the same or equivalent type of battery recommended bymanufactu-
rer. Do not open, do not charge, do not expose to high temperatures, do not expose to fire. Do not waste discharged batteries in environment but dispose of them in
special containers according to Law. Keep away from children.
•
XSAT WS from version 3.10p0 and later
•
Concorde Plus WS from version 1.00p3 and later
•
868,350Mhz
•
8
•
1 x MOD. CR2032
•
22 mA
•
14,5 mA
•
100 - 150 mt
•
- 20°C / +55°C
•
35 x 80 x 11
•
Shockproof plastic
INFORMATION ABOUT CONFORMITY TO DIRECTIVES 1999/5/CE (R&TTE)
! WARNING !
USE OF 3V LITHIUM BUTTON - BATTERY MODEL 2032.
CERTIFIED QUALITY
SYSTEM
UNI EN ISO 9001:2008
IST0867V1.2
Via Valsugana, 63
35010 (Padova) ITALY
Tel. 049 9698 411 / Fax. 049 9698 407
avs@avselectronics.it
Assistenza Tecnica: 049 9698 444
support@avselectronics.it
A B C
1
3
E
N
G
2
4
5
Werbung
