Device Description (Fig. 1-2); Scope Of Delivery (Fig. 2); Intended Use - Zgonc yellow PROFILINE YPL 1600 Originalbetriebsanleitung

1. Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device.
The operating instructions are intended to help the
user to become familiar with the device and take ad-
vantage of its application possibilities in accordance
with the recommendations.
The operating instructions contain important informa-
tion on how to operate the device safely, profession-
ally and economically, how to avoid danger, costly
repairs, reduce downtimes and how to increase reli-
ability and service life of the machine.
In addition to the safety instructions in these oper-
ating instructions and the safety instructions for the
machine mounted, you must also observe your coun-
try's regulations applicable to the operation of this
device and the electric power tool mounted.
Keep the operating instructions package with the
device at all times and store it in a plastic cover to
protect it from dirt and moisture. Read the instruction
manual each time before operating the device and
carefully follow its information.
The device can only be operated by persons who
were instructed concerning the operation of the ma-
chine and who are informed about the associated
dangers.
m Attention
The electric power tool mounted on the universal tool
stand may only be used by personnel who have been
trained in the use of the electric power tool and who
have been instructed with respect to the associated
hazards.
The minimum age requirement must be complied
with.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
In addition to the safety instructions in this operating
manual and the separate regulations of your country,
the generally recognised technical rules relating to
the operation of such devices must also be observed.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information.

2. Device description (fig. 1-2)

1. Mitre Saw Stand
2. Support bracket
3. Star knob screw (short)
4. Roller support
5. Mounting tube
6. Star knob screw (long)

3. Scope of delivery (fig. 2)

Mitre Saw Stand (1 Pcs.)
Support bracket (2 Pcs.)
Roller support (2 Pcs.)
Star knob screw; long (2 Pcs.)
Star knob screw; short (4 Pcs.)
Socket head screw, M6x60 mm (4 Pcs.)
Nut M6 (4 Pcs.)
Washers 6 mm (4 Pcs.)
Spring washer (4 Pcs.)
Manual (1 Pcs.)

4. Intended use

Always observe the proper use of your universal tool
stand.
The universal tool stand is designed for use with tab-
letop devices such as mitre saws, scroll saws, circu-
lar table saws, etc.
Electric power tools without suitable mounting holes
are not permitted to be fitted to the universal tool
stand and shall not be operated in conjunction with
the universal tool stand.
Electric power tools must be firmly bolted to the uni-
versal tool stand before starting them up.
The universal tool stand is also designed as a work-
piece support when working with mitre saws, scroll
saws, circular table saws, and other similar electric
power tools.
The maximum workpiece length is 3 m.
Additional workpiece supports may have to be used
(e.g. a roller trestle) in order to prevent longer work-
pieces tilting.
Attention: Ensure that the workpiece support is se-
cure and not tilted!
Do not use the universal tool stand as a ladder or
as scaffolding. Ensure that all handgrips, nuts and
screws are tightened before use. Electric power tools
11 І 16