Automatic Shutoff; Factory Settings; Led Indicator; Repairs And Maintenance - Cellular Line BTSPLITTER35 Bedienungsanleitung

Notes:
- After turning on, BTSPLITTER35 will connect to the last connected devi-
ce and will proceed to connect with devices according to the coupling
order until connection is successfully completed . If BTSPLITTER35 does
not successfully connect with a device, it will remain in search mode for
2 minutes .
During manual connection, hold down the button for 2 seconds and the
-
connection with the devices in the coupling list will be performed auto-
matically .

5. automatic shutoff

BTSPLITTER35 turns itself off automatically if in stand-by mode or without a
connection for more than 5 minutes .

6. Factory settings

When off, press the MFB button for a few seconds; the blue LED will flash
for 1 second then the red and blue LEDs will flash intermittently for a few
seconds and finally the red LED will flash for 1 second .
7. "reduced listening volume" function
Some audio devices could have an audio output with an overly high vo-
lume causing sound degradation (distortion) . This function reduces the
BTSPLITTER35 input sensitivity level to 6db, allowing for clean listening,
without distortions .
activate the function
After having connected the BTSPLITTER35 with one or two devices, briefly
press the MFB button once; the BTSPLITTER35 input sensitivity will lower to
6dB and the red LED will flash twice every 3 seconds .
deactivate "reduced listening volume" function
Briefly press the MFB button once as for activation; the transmitter music
volume will return to the previous level and the LED will flash blue .

8. led indicator

led indicator
Search for the first device (coupling
mode)
Search for the second device
(coupling mode)
Connect the first device
Connect the second device
Do not connect the device
18
Transmitter status
The red and blue LEDS will
flash intermittently
The blue LED will flash quickly
The blue LED will flash once
every second
The blue LED will flash twice
every second .
The blue LED will flash once
every 2 seconds
A device is already connected
Two devices are already connected
Battery level low
Charging
Charging complete

- rePairs aNd maiNTeNaNCe

Before using the BTSPLITTER35, read the following instructions in order to
ensure many years of use of the product .
Keep it in a dry place and do not expose to humidity to avoid damage to
-
the internal circuits .
Do not expose the product to sunlight or keep it in a very hot location .
-
High temperatures reduce the life of electronic devices and deform
some plastic elements .
Do not expose the BTSPLITTER35 to excessive temperatures that could
-
damage the internal circuits .
Do not attempt to dismantle the product . If this is done by non profes-
-
sionals it could damage the product .
Do not drop the product in order to avoid damaging the internal circuits .
-
Do not use chemical products or strong detergents to clean the device .
-
Do not scratch the surfaces with sharp or pointed objects .
-
If the product is not operating properly, in order to use the warranty you
must return it to the location where it was purchased along with the receipt
proving the data of purchase . The personnel will assist you in solving the
problem .
any tampering or damage voids the warranty.

- FaQ

1. What should i do if the BTsPliTTer35 will not turn on?
Try to charge it, making sure the red LED lights up . Otherwise try using a
different USB port or USB battery charger .
2. What should i do if the BTsPliTTer35 does not couple and connect
with the Bluetooth® receiver?
a) Make sure the Bluetooth® receiver supports the A2DP profile .
b) Make sure the Bluetooth® receiver is not more than 5 meters away .
c) Make sure the Bluetooth® receiver is in coupling mode .
The blue LED will flash once
every 4 seconds
The blue LED will flash twice
every 4 seconds .
The red LED will flash three
times every 30 seconds .
The red LED remains lit
LED off
IT
EN
FR
ES
DE