Environments: E1 (residential), E2 (commercial and light industrial), E3 (urban outdoors), E4 (controlled EMC environment, ex. TV studio). The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.
Seite 20
Table of Contents Overview................21 Additional Menu Items ...........22 Components of the DSBK-1820 ........31 Installation................32 Table of Contents...
Overview The DSBK-1820 HD Up-Converter Board is an optional board for installation in the Sony DSR-1800/1800P/1800A/1800AP Digital Videocassette Recorder or Sony DSR-1600/1600P/1600A/1600AP Digital Videocassette Player. The principal features of this board are as follows. • An SD video signal from DSR-1800/1800P/1800A/1800AP or DSR-...
EXT/REGEN. • Installing this board requires a DSR-1800/1800P/1800A/1800AP or DSR-1600/1600P/1600A/1600AP upgrade. For details, contact your Sony dealer or a Sony service representative. Note Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND...
Seite 23
Level 1 Level 2 Level 3 Settings LINE SELECT: Set 1080i: Select 1080i CONVERTER the line standard 720P: Select 720P conversion (59.94 Hz only) (1080i/720P) for HD SDI output. Notes • If the setting is changed, the new setting will be effective when the power is turned on after once turned...
Seite 24
Level 1 Level 2 Level 3 Settings TIME CODE: Set the 9P TC PHASE: Set SD: Set to SD output timecode the basis for phase settings. response to HD: Set to HD output timecode phase sensing through the DSR-1800/ 1800P/1800A/ 1800AP or DSR- 1600/1600P/ 1600A/1600AP...
Seite 25
Level 1 Level 2 Level 3 Settings SYNC PHASE (HD): COARSE: Make 0 - 80H - FFH Make coarse coarse adjustment of the adjustment of the H sync phase of H sync phase the HD video FINE: Make fine 0 - 20H - 3FH signal output adjustment of the from the HD SDI...
Seite 26
Level 1 Level 2 Level 3 Settings ASPECT FLAG: OFF: The up- Specify the converter mode treatment of an ignores the aspect ratio aspect ratio identification identification signal included signal, and within the SD follows setting of signal. UP CONV MODE.
Seite 27
Level 1 Level 2 Level 3 Settings POSITION ADJUST: H CROP: If “EDGE- 0 - 20H - 3FH Adjust the CROP” is position from selected in UP which the H crop CONV MODE, or letterbox mode adjust H crop image is (the horizontal extracted from position of the...
Seite 28
Level 1 Level 2 Level 3 Settings UP CONV PROC: FIELD: Use video When converting fields SD to HD, select FRAME: Use video how the original frames video is ADAPTIVE processed. (standard mode): Determine from movement in the original video whether to use frames or fields for conversion.
Seite 29
Level 1 Level 2 Level 3 Settings IMAGE ENHANCER: DETAIL GAIN: Set 0 - 20H - 3FH Adjust up- the sharpness of converter image edge enhancer. enhancement. LIMITER: Set the 0 - 10H - 1FH maximum level of the detail signal added to emphasize the original signal.
Seite 30
Level 1 Level 2 Level 3 Settings BG COLOR: Set the BLACK: Black background color GRAY: Gray for otherwise BLUE: Blue blank portions created in up- conversion. UP CONV MODE settings and methods of conversion from 4:3 to 16:9 a) EDGE-CROP 4 : 3 16 : 9 b) LETTER BOX...
Components of the DSBK-1820 The DSBK-1820 consists of the following items. SDI-93 board HD SDI OUT Connector label for the rear panel Screw A (M3 × 3, silver-colored) Screw B (M3 × 2, silver-colored) Overview...
If this option is installed incorrectly, personal injury or damage to peripheral items may occur due to fire, shock, or other accidental circumstances. To avoid such risks, consult your Sony dealer or a Sony service representative for installation. To install the DSBK-1820 in the DSR-1800/1800P/1800A/1800AP or DSR-1600/1600P/1600A/1600AP, proceed as follows.
Seite 33
Connector panel (SDI Input) Connector panel (HD SDI) Connector panel (AES/EBU Input) SDI-93 board Remove the outer BNC connector and the harness from the HD SDI connector panel. Connector panel (HD SDI) Harness Outer BNC connector Replace the HD SDI connector panel (see following figure 1), and connect the harness removed in step 2 to the temporary joint connector on the SDI-93 board (see following figure 2).
Seite 34
SDI-93 board Harness Connector panel (HD SDI) (Temporary joint connector) Installation of the DSBK-1820 (either in DSR-1800/1800P/1800A/1800AP or DSR-1600/1600P/1600A/ 1600AP) Remove the top panel of the DSR-1800/1800P/1800A/1800AP or DSR-1600/1600P/1600A/1600AP (hereinafter called the unit). Remove the three blank panels from the rear panel of the unit. Installation...
Seite 35
Rear panel of the unit Remove to install the DSBK-1820 How to remove a blank panel Remove the rear panel. Rear panel Affix the supplied connector label (HD SDI OUT) for the rear panel to cover the SDTI (QSDI) display portion of the rear panel. HD SDI OUT DV IN/OUT SDTI(QSDI)
Seite 36
Top view of the unit: Attachment screw Rear side of holes (5 holes) the unit Attach the SDI-93 board to the unit. The fifth screw hole is under the TX-96 board, so remove the board before attaching as shown below. 1Press down on the center of the SDI-93 board so as to connect the connectors of the board to the connectors of the unit.
Seite 37
2Remove the screws in all four corners of the TX-96 board. TX-96 board 3Lift up the TX-96 board, disconnect it from the SDI-93 board, and move it to the side. Fasten the supplied screw A in hole Screw A TX-96 board SDI-93 board Hole I...
Seite 38
Screw B Screw A Replace the rear panel of the unit, then the top panel. Installation...
Seite 39
Le fabricant de ce produit est Sony Corporation, 1-7-1 Konan, Minato- ku, Tokyo, Japon. Le représentant autorisé pour EMC et la sécurité des produits est Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Allemagne. Pour toute question concernant le service ou la garantie, veuillez consulter les adresses indiquées dans les documents de service...
Seite 40
Sommaire Aperçu..................41 Postes de menu additionnels ...........42 Composants de la DSBK-1820 ........51 Installation................52 Sommaire...
Aperçu La carte de convertisseur élévateur de fréquence HD DSBK-1820 est une carte optionnelle prévue pour être installé dans le magnétoscope enregistreur numérique DSR-1800/1800P/1800A/1800AP Sony ou le lecteur vidéocassette numérique DSR-1600/1600P/1600A/1600AP de Sony. Les fonctions principales de cette carte sont les suivantes.
1800P/1800A/1800AP ou DSR-1600/1600P/1600A/1600AP. L’installation de cette carte exige une mise à niveau du micrologiciel de l’enregistreur de disque. Pour les détails, contactez votre distributeur Sony ou un représentant du service après-vente Sony. Remarque Vérifiez toujours que l’appareil fonctionne correctement avant l’utilisation.
Seite 43
Niveau 1 Niveau 2 Niveau 3 Réglages LINE SELECT: Règle 1080i: Sélectionne CONVERTER la conversion de 1080i ligne standard 720P: Sélectionne (1080i/720P) 720P (59,94 Hz pour la sortie HD uniquement) SDI. Remarques • Si le réglage est modifié, le nouveau réglage prendra effet après que le système ait été...
Seite 44
Niveau 1 Niveau 2 Niveau 3 Réglages TIME CODE: Réglez 9P TC PHASE: Régle SD: Régle sur la le paramètre du la base pour la phase de sortie code temporel. réponse à la détection du HD: Régle sur la code temporel à phase de sortie travers le connecteur...
Seite 45
Niveau 1 Niveau 2 Niveau 3 Réglages SYNC PHASE (HD): COARSE: Effectue 0 - 80H - FFH Effectue un un réglage réglage approximatif de approximatif de la phase de la phase de synchro H synchro H du FINE: Effectue un 0 - 20H - 3FH signal vidéo HD réglage précis de...
Seite 46
Niveau 1 Niveau 2 Niveau 3 Réglages ASPECT FLAG: OFF: Le mode Spécifie le convertisseur traitement du élévateur ignore signal le signal d’identification du d’identification du rapport d’aspect rapport d’aspect, compris dans le et suit le signal SD. paramètre de UP CONV MODE.
Seite 47
Niveau 1 Niveau 2 Niveau 3 Réglages POSITION ADJUST: H CROP: Si « EDGE- 0 - 20H - 3FH Ajustez la CROP » est position à partir sélectionné au de laquelle poste de UP l’image du mode CONV MODE, H crop ou ajuste H crop (la letterbox est position...
Seite 48
Niveau 1 Niveau 2 Niveau 3 Réglages UP CONV PROC: FIELD: Utilise les Lors de la trames vidéo conversion SD à FRAME: Utilise les HD, sélectionne cadres vidéo le traitement de ADAPTIVE (mode la vidéo originale. standard): Détermine l’utilisation de cadres ou de trames pour la conversion à...
Seite 49
Niveau 1 Niveau 2 Niveau 3 Réglages IMAGE ENHANCER: DETAIL GAIN: Ajuste 0 - 20H - 3FH Ajuste le le rehausseur rehausseur d’image du d’image du convertisseur convertisseur élévateur. élévateur. LIMITER: Règle le 0 - 10H - 1FH niveau maximum du signal de détail ajouté...
Seite 50
Niveau 1 Niveau 2 Niveau 3 Réglages BG COLOR: Règle la BLACK: Noir couleur du fond GRAY: Gris pour les autres BLUE: Bleu zones vides créées en conversion élévatrice. Paramètres UP CONV MODE et méthodes de conversion du format 4:3 au 16:9 a) EDGE-CROP 4 : 3 16 : 9...
Composants de la DSBK-1820 La carte DSBK-1820 comprend les éléments suivants. Carte SDI-93 HD SDI OUT Etiquette de connecteur pour la plaque arrière Vis A (M3 × 3, argentées) Vis B (M3 × 2, argentées) Aperçu...
DSR-1800/1800P/1800A/1800AP ou DSR-1600/1600P/1600A/1600AP. L’installation de cette carte exige une mise à niveau du micrologiciel de l’enregistreur de disque. Pour les détails, contactez votre distributeur Sony ou un représentant du service après-vente Sony. Installation dans le DSR-1600/1600P/1600A/1600AP Avant d’installer la DSBK-1820 dans le DSR-1600/1600P/1600A/...
Seite 53
Plaque à connecteurs (Entrée SDI) Plaque à connecteurs (HD SDI) Plaque à connecteurs (Entrée AES/EBU) Carte SDI-93 Retirez le connecteur BNC extérieur et le câblage de la plaque à connecteurs HD SDI. Plaque à connecteurs (HD SDI) Câblage Connecteur BNC extérieur Replacez la plaque à...
Seite 54
Carte SDI-93 Câblage Plaque à connecteurs (HD SDI) CN1 (Connecteur de jonction temporaire) Installation de la DSBK-1820 (soit dans le DSR-1800/1800P/1800A/ 1800AP soit dans le DSR-1600/1600P/1600A/1600AP) Retirez la plaque supérieure du DSR-1800/1800P/1800A/1800AP ou du DSR-1600/1600P/1600A/1600AP (appelé unité par la suite). Retirez les trois plaques de suppression de la plaque arrière de l’unité.
Seite 55
Retirez pour installer la Plaque arrière de DSBK-1820 l’unité Comment retirer la plaque de suppression Retirez la plaque arrière. Plaque arrière Apposez l’étiquette de connecteur fournie (HD SDI OUT) pour la plaque arrière pour couvrir la portion de SDTI (QSDI) de la plaque arrière.
Seite 56
Alignez les cinq orifices de vis de la carte SDI-93 avec ceux de l’unité. Vue du dessus de l’unité: Fixation dans les orifices Face arrière de de vis (5 orifices) l’unité Fixez la carte SDI-93 à l’unité. Le cinquième orifice de vis se trouve sous la carte TX-96, donc vous devez retirer la carte avant de la fixation comme indiqué...
Seite 57
2Retirez les vis des quatres coins de la carte TX-96. Carte TX-96 3Soulevez la carte TX-96, retirez-la de la carte SDI-93 et mettez-la sur le côté. Fixez la vis A fournie dans l’orifice I. Vis A Carte TX-96 Carte SDI-93 Orifice I 4Replacez la carte TX-96 de façon à...
Seite 58
Vis B Vis A Replacez la plaque arrière de l’unité puis la plaque supérieure. Installation...
(Wohnbereich), E2 (kommerzieller und in beschränktem Maße industrieller Bereich), E3 (Stadtbereich im Freien) und E4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio). Der Hersteller dieses Produkts ist Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Japan. Der autorisierte Repräsentant für EMV und Produktsicherheit ist Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Deutschland.
Seite 60
Inhaltsverzeichnis Kurzbeschreibung..............61 Weitere Menüpositionen ..........62 Bestandteile der DSBK-1820 .........71 Einbau..................72 Inhaltsverzeichnis...
Kurzbeschreibung Die DSBK-1820 HD-Aufwärtswandler-Karte ist eine optionale Karte zum Einbau in die Digitalvideorecorder DSR-1800/1800P/1800A/ 1800AP von Sony oder der Digitalvideorecorder DSR-1600/1600P/ 1600A/1600AP von Sony. Die Karte weist folgende wesentliche Eigenschaften auf. • Aufwärtswandlung eines SD-Videosignals der Wiedergabe des DSR- 1800/1800P/1800A/1800AP oder DSR-1600/1600P/1600A/1600AP in ein HD-Videosignal und Ausgabe aus zwei HD SDI-Ausgängen (1...
Wenden Sie sich für nähere Einzelheiten an Ihren Sony-Händler oder Sony-Service-Mitarbeiter. Hinweis Bestätigen Sie vor dem Gebrauch immer, dass das Gerät richtig arbeitet. SONY KANN KEINE HAFTUNG FÜR SCHÄDEN JEDER ART, EINSCHLIESSLICH ABER NICHT BEGRENZT AUF KOMPENSATION ODER ERSTATTUNG, AUFGRUND VON VERLUST VON AKTUELLEN ODER ERWARTETEN PROFITEN DURCH FEHLFUNKTION DIESES GERÄTS ODER...
Seite 63
Level 1 Level 2 Level 3 Einstellungen LINE SELECT: 1080i: Zur Wahl von CONVERTER Einstellung der 1080i Standard- 720P: Zur Wahl von Zeilenumwand- 720P (nur 59,94 lung (1080i/ 720P) für die HD SDI-Ausgabe. Hinweise • Bei Änderung der Einstellung wird die neue Einstellung übernommen, nachdem der Strom...
Seite 64
Level 1 Level 2 Level 3 Einstellungen TIME CODE: 9P TC PHASE: SD: Einstellung der Nehmen Sie die Stellen Sie über Timecode- Ausgabephase Einstellungen Fernanschluss HD: Einstellung der vor. RS-422A des DSR-1800/ Ausgabephase 1800P/1800A/ 1800AP oder 1600/1600P/ 1600A/1600AP die Grundlage Berücksichtigung des Timecode- Tasters ein.
Seite 65
Level 1 Level 2 Level 3 Einstellungen SYNC PHASE (HD): COARSE: Vornahme 0 - 80H - FFH Vornahme der Grobeinstellung Grobeinstellung der H-Synchro- der H- nisationsphase Synchronisa- des vom HD SDI tionsphase OUTPUT- FINE: Vornahme der 0 - 20H - 3FH Anschluss Feineinstellung ausgegebenen...
Seite 66
Level 1 Level 2 Level 3 Einstellungen ASPECT FLAG: OFF: Der Spezifizierung Aufwärtswand- des Vorgehens lungsmodus bei einem im SD- ignoriert das Signal Seitenverhältnis- vorhandenen Bestimmungs- Seitenverhältnis- signal und richtet Bestimmungs- sich nach der signal. Einstellung von UP CONV MODE. Hinweis ON: Der Wenn das...
Seite 67
Level 1 Level 2 Level 3 Einstellungen POSITION ADJUST: H CROP: Wenn unter 0 - 20H - 3FH Stellen Sie die UP CONV Position ein, von MODE „EDGE der aus das H- CROP“ gewählt Schnitt- oder ist, Einstellung Letterbox- des H-Schnitts Modus-Bild des (die horizontale Originalvideos...
Seite 68
Level 1 Level 2 Level 3 Einstellungen UP CONV PROC: FIELD: Verwendung Wahl der Verarbeitung des Videohalbbildern Originalvideos FRAME: Verwendung bei der Umwandlung von Videovollbildern SD zu HD. ADAPTIVE (Standardmo- dus): Festlegung auf Grund der Bewegung im Originalvideo, ob Voll- oder Halbbilder für die Wandlung verwendet...
Seite 69
Level 1 Level 2 Level 3 Einstellungen IMAGE ENHANCER: DETAIL GAIN: 0 - 20H - 3FH Einstellung der Einstellung der Aufwärtswand- Schärfe der lungs-Bildverbes- Randverbesse- serung. rung. LIMITER: Einstellung 0 - 10H - 1FH Höchstniveaus Einzelsignals, das zur Verstärkung des Originalsignals hinzugefügt wird.
Seite 70
Level 1 Level 2 Level 3 Einstellungen H/V RATIO: 0 - 03H - 7H Einstellung des horizontalen/ vertikalen Verhältnisses für die Randverbes- serung. GAMMA LEVEL: 0 - 08H - 10H Einstellung der Steigung der Gamma- Kompensations- kurve. BG COLOR: BLACK: Schwarz Einstellung der GRAY: Grau Hintergrundfar-...
Bestandteile der DSBK-1820 Die DSBK-1820 weist folgende Bestandteile auf. Leiterplatte SDI-93 HD SDI OUT Anschlussetikett für die Rückseite Schraube A (M3 × 3, Schraube B (M3 × 2, silberfarben) silberfarben) Kurzbeschreibung...
Bei unsachgemäßem Einbau besteht die Gefahr von Verletzungen sowie Schäden an Peripherieausrüstungen auf Grund von Brand, elektrischem Schlag oder anderweitigen Problemen. Wenden Sie sich zum Einbau daher an Ihren Sony-Händler oder Sony-Service- Mitarbeiter. Verfahren Sie zum Einbau der DSBK-1820 in den DSR-1800/1800P/ 1800A/1800AP oder DSR-1600/1600P/1600A/1600AP wie folgt.
Seite 73
Anschlussfeld (SDI-Eingang) Anschlussfeld (HD SDI) Anschlussfeld (AES/ EBU-Eingang) Leiterplatte SDI-93 Entfernen Sie den äußerer BNC-Anschluss und den Kabelbaum vom HD SDI-Anschlussfeld. Anschlussfeld (HD SDI) Kabelbaum Äußerer BNC-Anschluss Bringen Sie das HD SDI-Anschlussfeld an (siehe folgende Abbildung 1) und schließen Sie den im Schritt 2 entfernten Kabelbaum an den temporären gemeinsamen Anschluss auf der Karte SDI-93 an (siehe folgende Abbildung 2).
Seite 74
Leiterplatte SDI-93 Kabelbaum Anschlussfeld (HD SDI) CN1 (Temporärer gemeinsamer Anschluss) Einbau der DSBK-1820 (entweder in den DSR-1800/1800P/1800A/ 1800AP oder DSR-1600/1600P/1600A/1600AP) Entfernen Sie die obere Platte des DSR-1800/1800P/1800A/ 1800AP oder DSR-1600/1600P/1600A/1600AP (im Folgenden als „Gerät“ bezeichnet). Entfernen Sie die drei Blindplatten von der Rückseite des Geräts. Einbau...
Seite 75
Entfernen, um die DSBK-1820 einzubauen Rückseite des Geräts Entfernen einer Blindplatte Entfernen Sie die Rückseite. Rückseite Befestigen Sie das mitgelieferte Anschlussetikett (HD SDI OUT) für die Rückseite, um die SDTI- (QSDI-) Anzeigefelder der Rückseite abzudecken. HD SDI OUT DV IN/OUT SDTI(QSDI) Gleichen Sie alle fünf Befestigungslöcher der Karte SDI-93 mit denen des Geräts ab.
Seite 76
Obere Geräteansicht: Angebrachte Befestigungslöcher Rückseite des (5 Löcher) Geräts Bringen Sie die Karte SDI-93 an das Gerät an. Das fünfte Befestigungsloch ist unter der Leitplatte TX-96, entfernen Sie also die Leitplatte vor dem unten beschriebenen Anbringen. 1Drücken Sie auf die Mitte der Karte SDI-93, so als würden Sie die Anschlüsse der Karte mit den Anschlüssen des Geräts verbinden.
Seite 77
2Entfernen Sie die Schrauben in allen vier Ecken der Leitplatte TX-96. Leiterplatte TX-96 3Heben Sie die Leitplatte TX-96 an, lösen Sie die Verbindung zur Karte SDI-93 und schieben Sie sie zur Seite. Befestigen Sie die mitgelieferte Schraube A im Loch I. Schraube A Leiterplatte TX-96 Leiterplatte...
Seite 78
Schraube B Schraube A Bringen Sie zuerst die Rückseite des Geräts und dann die obere Platte wieder an. Einbau...
Seite 79
E1 (residenziali), E2 (commerciali e industriali leggeri), E3 (esterni urbani) e E4 (ambienti EMC controllati, ad esempio studi televisivi). Il fabbricante di questo prodotto è la Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Giappone. La rappresentanza autorizzata per EMC e la sicurezza dei prodotti è la Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stoccarda, Germania.
Seite 80
Indice Descrizione................81 Voci di menu supplementari ...........82 Componenti del DSBK-1820 ..........91 Installazione................92 Indice...
Descrizione La scheda DSBK-1820 per la conversione a HD è una scheda opzionale che si può installare nei videoregistratori digitali Sony DSR-1800/ 1800P/1800A/1800AP o nei lettori digitali di videocassette Sony DSR- 1600/1600P/1600A/1600AP. Le caratteristiche principali di questa scheda sono descritte di seguito.
Sony o il rappresentante Sony. Nota Verificare sempre che l’apparecchio stia funzionando correttamente prima di usarlo. LA SONY NON SARÀ RESPONSABILE DI DANNI DI QUALSIASI TIPO, COMPRESI, MA SENZA LIMITAZIONE A, RISARCIMENTI O RIMBORSI A CAUSA DELLA PERDITA DI PROFITTI ATTUALI O PREVISTI DOVUTA A GUASTI DI QUESTO APPARECCHIO, SIA DURANTE IL PERIODO DI VALIDITÀ...
Seite 83
Livello 1 Livello 2 Livello 3 Impostazioni LINE SELECT: 1080i: Seleziona CONVERTER Imposta la 1080i conversione di 720P: Seleziona linea standard 720P (solo 59,94 (1080i/720P) per l’emissione HD SDI. Note • Se si cambia l’impostazione, la nuova impostazione sarà disponibile dopo aver spento e riacceso l’apparato.
Seite 84
Livello 1 Livello 2 Livello 3 Impostazioni TIME CODE: 9P TC PHASE: SD: Imposta la fase di Impostare le Impostare la uscita SD impostazioni del base di risposta HD: Imposta la fase codice del tempo. alla rilevazione di uscita HD del codice di tempo attraverso il connettore...
Seite 85
Livello 1 Livello 2 Livello 3 Impostazioni SYNC PHASE (HD): COARSE: Effettua 0 - 80H - FFH Effettua una una regolazione regolazione grossolana della grossolana della fase di fase di sincronizzazione sincronizzazione H per l’uscita del FINE: Effettua una 0 - 20H - 3FH segnale video regolazione HD dal...
Seite 86
Livello 1 Livello 2 Livello 3 Impostazioni ASPECT FLAG: OFF: Il modo di Specifica il conversione trattamento di un ignora il segnale segnale di di identificazione identificazione di del rapporto di rapporto di formato, e segue formato incluso l’impostazione di con il segnale UP CONV MODE.
Seite 87
Livello 1 Livello 2 Livello 3 Impostazioni POSITION ADJUST: H CROP: Se nella 0 - 20H - 3FH Regolare la voce di UP posizione dalla CONV MODE si quale il taglio H o è selezionato formato lettera “EDGE-CROP”, dell’immagine regolare il taglio viene estratto dal H (la posizione video originale.
Seite 88
Livello 1 Livello 2 Livello 3 Impostazioni UP CONV PROC: FIELD: Usa i campi Quando si video converte SD a FRAME: Usa i HD, selezionare fotogrammi video come viene ADAPTIVE (modo processato il standard): video originale. Determina dal movimento del video originale se si usa fotogrammi o...
Seite 89
Livello 1 Livello 2 Livello 3 Impostazioni IMAGE ENHANCER: DETAIL GAIN: 0 - 20H - 3FH Regola Imposta la l’intensificatore nitidezza della conversione dell’aumento del dell’immagine. bordo. LIMITER: Imposta il 0 - 10H - 1FH livello massimo del segnale particolare aggiunto per accentuare il segnale...
Seite 90
Livello 1 Livello 2 Livello 3 Impostazioni H/V RATIO: Imposta 0 - 03H - 7H il rapporto orizzontale/ verticale per l’aumento del bordo. GAMMA LEVEL: 0 - 08H - 10H Regola l’inclinazione della curva della gamma di compensazione. BG COLOR: Imposta BLACK: Nero il colore di fondo GRAY: Grigio...
Componenti del DSBK-1820 Il DSBK-1820 si compone delle seguenti parti. Scheda SDI-93 HD SDI OUT Etichetta del connettore per il pannello posteriore Vite A (M3 × 3, color argento) Vite B (M3 × 2, color argento) Descrizione...
DSR-1800/1800P/1800A/1800AP o DSR-1600/1600P/1600A/1600AP. L’installazione di questa scheda richiede un aggiornamento del firmware del registratore di dischi. Per dettagli, contattare il proprio rivenditore Sony o il rappresentante Sony. Installazione nel DSR-1600/1600P/1600A/1600AP Prima di installare il DSBK-1820 nel DSR-1600/1600P/1600A/ 1600AP, si devono rimuovere le seguenti parti.
Seite 93
Pannello del connettore (entrata SDI) Pannello del connettore (HD SDI) Pannello del connettore (entrata AES/EBU) Scheda SDI-93 Rimuovere il connettore di uscita BNC e l’imbracatura dal pannello del connettore HD SDI. Pannello del connettore (HD SDI) Cablaggio Connettore di uscita BNC Riporre il pannello del connettore HD SDI (vedere la seguente illustrazione 1) e collegare l’imbracatura rimossa al passo 2 al connettore di unione temporaneo sulla scheda SDI-93 (vedere la...
Seite 94
Scheda SDI-93 Cablaggio Pannello del connettore (HD SDI) CN1 (Connettore di unione temporaneo) Installazione del DSBK-1820 (sia per DSR-1800/1800P/1800A/ 1800AP che DSR-1600/1600P/1600A/1600AP) Rimuovere il pannello superiore del DSR-1800/1800P/1800A/ 1800AP o DSR-1600/1600P/1600A/1600AP (d’ora in poi chiamato unità). Rimuovere i tre pannelli ciechi dal pannello posteriore dell’unità. Installazione...
Seite 95
Pannello posteriore Rimuovere per installare il dell’unità DSBK-1820 Come rimuovere il pannello cieco Rimuovere il pannello posteriore. Pannello posteriore Attaccare l’etichetta del connettore fornita (HD SDI OUT) per il pannello posteriore per coprire la parte del display SDTI (QSDI) del pannello posteriore. HD SDI OUT DV IN/OUT SDTI(QSDI)
Seite 96
Vista dall’alto dell’unità: Buchi delle viti di Lato posteriore attacco (5 buchi) dell’unità Attaccare la scheda SDI-93 all’unità. Il quinto buco della vite si trova sotto la scheda TX-96, quindi rimuovere la scheda prima di attaccare come mostrato sotto. 1Premere sul centro della scheda SDI-93 in modo tale da collegare i connettori della scheda ai connettori dell’unità.
Seite 97
2Rimuovere le viti dai quattro angoli della scheda TX-96. Scheda TX-96 3Sollevare la scheda TX-96, scollegarla dalla scheda SDI-93 e muoverla sul lato. Avvitare la vite A fornita nel buco I. Vite A Scheda TX-96 Scheda SDI-93 Buco I 4Riporre la scheda TX-96 collegata alla scheda SDI-93 e avvitare le viti ai quattro angoli.
Seite 98
Vite B Vite A Riporre il pannello posteriore dell’unità, quindi il pannello superiore. Installazione...
Seite 99
E3 (exteriores urbanos), y E4 (entorno con EMC controlada, p. ej., estudio de televisión). El fabricante de este producto es Sony Corporation, con dirección en 1- 7-1 Konan, Minato-ku, Tokio, Japón. El Representante autorizado para EMC y seguridad del producto es Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Alemania.
Seite 100
Índice Descripción general ............101 Opciones adicionales del menú ........102 Componentes de la tarjeta DSBK-1820 ......111 Instalación ................112 Índice...
La tarjeta DSBK-1820 de conversión a formato HD es una tarjeta opcional que puede instalarse en la videograbadora digital DSR-1800/ 1800P/1800A/1800AP de Sony o el reproductor digital de videocasetes DSR-1600/1600P/1600A/1600AP de Sony. Éstas son las principales características de la tarjeta: •...
La instalación de esta tarjeta requiere una mejora del firmware de la grabadora. Para más información, póngase en contacto con su distribuidor de Sony o el servicio de asistencia de Sony. Nota Verifique siempre que esta unidad funciona correctamente antes de utilizarlo.
Seite 103
Nivel 1 Nivel 2 Nivel 3 Ajustes LINE SELECT: 1080i: Selecciona CONVERTER Ajusta la 1080i conversión 720P: Selecciona estándar de la 720P (sólo 59,94 línea (1080i/ 720P) para la salida HD SDI. Notas • Si se cambia el ajuste, el nuevo ajuste será...
Seite 104
Nivel 1 Nivel 2 Nivel 3 Ajustes TIME CODE: Ajuste 9P TC PHASE: SD: Ajustado a la el código de Ajusta los fase de salida SD tiempo. fundamentos de HD: Ajustado a la respuesta para el fase de salida detector de código de tiempo mediante el conector remoto...
Seite 105
Nivel 1 Nivel 2 Nivel 3 Ajustes SYNC PHASE (HD): COARSE: Realiza un 0 - 80H - FFH Realiza un ajuste ajuste general de general de la la fase de fase de sincronización de sincronización de H en la salida de FINE: Realiza un 0 - 20H - 3FH la señal de vídeo...
Seite 106
Nivel 1 Nivel 2 Nivel 3 Ajustes ASPECT FLAG: OFF: El modo del Indica el convertidor tratamiento de ignora la señal una señal de de identificación identificación de de la relación de la relación de aspecto, y aspecto incluida mantiene los en la señal SD.
Seite 107
Nivel 1 Nivel 2 Nivel 3 Ajustes POSITION ADJUST: H CROP: Si está 0 - 20H - 3FH Ajuste la posición seleccionado desde la cual la “EDGE-CROP” imagen del modo en UP CONV buzón o de MODE, ajusta el recorte H se recorte H (la extrae del vídeo posición...
Seite 108
Nivel 1 Nivel 2 Nivel 3 Ajustes UP CONV PROC: FIELD: Utiliza Cuando campos de vídeo convierta SD en FRAME: Utiliza HD, selecciona el fotogramas de modo de vídeo procesado del ADAPTIVE (modo vídeo original. estándar): Determina a través del movimiento del vídeo original si utilizar...
Seite 109
Nivel 1 Nivel 2 Nivel 3 Ajustes IMAGE ENHANCER: DETAIL GAIN: Ajusta 0 - 20H - 3FH Ajusta el la nitidez para optimizador de mejorar el borde. imágenes del LIMITER: Ajusta el 0 - 10H - 1FH convertidor. nivel máximo de la señal de detalle agregada para realzar la...
Seite 110
Nivel 1 Nivel 2 Nivel 3 Ajustes BG COLOR: Ajusta BLACK: Negro el color del fondo GRAY: Gris de las porciones BLUE: Azul en blanco que se hayan generado con la conversión. Ajustes de UP CONV MODE y de los métodos de conversión de 4:3 a 16:9 a) EDGE-CROP 4 : 3 16 : 9...
Componentes de la tarjeta DSBK-1820 La tarjeta DSBK-1820 contiene los siguientes elementos. Tarjeta SDI-93 HD SDI OUT Etiqueta de conexión del panel posterior Tornillo A (M3 × 3, plateados) Tornillo B (M3 × 2, plateados) Descripción general...
Para evitar estos riesgos, póngase en contacto con su representante de Sony o el servicio técnico de Sony para la instalación. Para instalar la tarjeta DSBK-1820 en la videograbadora DSR-1800/ 1800P/1800A/1800AP o DSR-1600/1600P/1600A/1600AP, siga las siguientes instrucciones.
Seite 113
Panel de conexiones (entrada SDI) Panel de conexiones (HD SDI) Panel de conexiones (entrada AES/EBU) Tarjeta SDI-93 Extraiga el conector BNC exterior y el mazo de cables del panel de conexiones HD SDI. Panel de conexiones (HD SDI) Mazo de cables Conector BNC exterior Sustituya el panel de conexiones HD SDI (véase siguiente figura 1) y conecte el mazo extraído en el paso 2 al conector de empalme...
Seite 114
Tarjeta SDI-93 Mazo de cables Panel de conexiones (HD SDI) CN1 (Conector de empalme temporal) Instalación de la DSBK-1820 (ya sea en DSR-1800/1800P/1800A/ 1800AP o en DSR-1600/1600P/1600A/1600AP) Extraiga el panel superior de la DSR-1800/1800P/1800A/1800AP o de la DSR-1600/1600P/1600A/1600AP (llamada la unidad a partir de aquí).
Seite 115
Panel posterior de la Extraiga para instalar la DSBK-1820 unidad Cómo extraer un panel ciego Extraiga el panel posterior. Panel posterior Fije la etiqueta de conexión suministrada (HD SDI OUT) al panel posterior para cubrir la parte de visualización SDTI (QSDI) del panel trasero.
Seite 116
Vista superior de la unidad: Orificios para tornillos Lado posterior de sujeción (5 orificios) de la unidad Fije la tarjeta SDI-93 de la unidad. El quinto orificio para tornillo se encuentra bajo la tarjeta TX-96, de modo que extraiga la tarjeta antes de acoplarla tal y, como se muestra a continuación.
Seite 117
2Extraiga los tornillos de las cuatro esquinas de la tarjeta TX-96. Tarjeta TX-96 3Levante la tarjeta TX-96, desconéctela de la tarjeta SDI-93 y desplácela a un lado. Fije el tornillo suministrado A en el orificio I. Tornillo A Tarjeta TX-96 Tarjeta SDI-93 Orificio I...
Seite 118
Tornillo B Tornillo A Sustituya el panel posterior de la unidad y, a continuación, el panel superior. Instalación...