Technical Data; Eu Declaration Of Conformity - Chicago Pneumatic CP7769 Bedienungsanleitung

Impact Wrench

Technical data

Max. pressure: 6.3 BAR / 90 PSI MAX.
RPM ft.Lb
CP7769 6500 300-
1080
CP7769-6 6500 300 -
1080
CP7779 6500 300 -
1080
(dB(A))
CP7769 96.8
CP7769-6 96.8
CP7779 96.8
Uncertainty 3 dB(A), in accordance with ISO 15744. For
Sound power level, add 11 dB(A)
Vibration standard : ISO-28927-2
Declarations
Noise and vibration
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. These declared val-
ues are not adequate for use in risk assessments and values
measured in individual work places may be higher. The ac-
tual exposure values and risk of harm experienced by an indi-
vidual user are unique and depend upon the way the user
works, the workpiece and the workstation design, as well
upon the exposure time and the physical condition of the
user.
We, CHICAGO PNEUMATIC Tool Co. LLC, cannot be
held liable for the consequences of using the declared values,
instead of values reflecting the actual exposure, in an individ-
ual risk assessment in a work place situation over which we
have no control.
This tool may cause hand-arm vibration syndrome if its use
is not adequately managed. An EU guide to managing hand-
arm vibration can be found by accessing
rop.eu/index.php and selecting 'Tools' then 'Legislation'.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.
Nm kg
407 - 3.15 6.9
1464
407 - 3.75 8.3
1464
407 - 3.3 7.2
1464
2 2
(m/s ) K (m/s )
12.97 1.5
12.97 1.5
12.97 1.5
http://www.pneu-

EU DECLARATION OF CONFORMITY

We, CHICAGO PNEUMATIC Tool Co. LLC, 1815 Club-
house Road, Rock Hill, SC 29730, declare under our sole re-
sponsibility that the product (with name, type and serial
number, see front page) is in conformity with the following
Directive(s):
2006/42/EC (17/05/2006)
lb
Harmonized standards applied:
EN ISO 11148-6:2012
Authorities can request relevant technical information from:
Pascal Roussy, R&D Manager, Ets Georges Renault, 38 rue
Bobby Sands, BP10273 44818 Saint Herblain, France
Saint-Herblain,
Pascal ROUSSY
Signature of issuer
Statement of use
This product is designed for installing and removing threaded
fasteners in wood, metal or plastic.
No other use permitted. For professional use only.
WARNING Risk of injury
If the torque is higher than 50 Nm, a reaction bar
►
must be used.
The reaction bar is designed for absorbing the reac-
tion torque of assembly power tools.
Product specific instructions
Operation
See figures on page 2.
• Fix the accessories properly to the tool.
• Connect device to a clean and dry air supply.
• To start the machine, pull the trigger (A). Machine speed
is increase by increasing pressure on the trigger. Release
the trigger to stop.
• To switch rotation, push the switch (B). Use the reverse
switch (B) only when the drive spindle comes to a com-
plete stop. Changing the speed before the drive spindle
stops may damage the machine.
• To adjust output power, turn the regulator (B).
Clutch lubrication
Use 0.5 oz. (14 g) of CP Pneu-Lube Synthetic Clutch grease.
7