Troubleshooting; Maintenance - bem wireless speaker trio Bedienungsanleitung

Operation Details
Power on / Power off
Base : Press the power button to turn on the base
of Speaker Trio. The Bluetooth© indicator will light
up to signify the unit is on and ready to be paired.
Press the power button again to turn off the base
and the Bluetooth indicator light will go out.
Speakers: Press the power button to turn the
speaker on. The white light on the base will light
up to signify the unit is on. Press the power button
again to turn off the speaker and the white base
light will also go out.
Please note, always make sure to first turn on the
base unit before turning on the speakers
Play modes
Bluetooth mode: play an audio signal from the
connected Bluetooth© device.
AUX mode: play an audio signal from the
connected "wired" device.
Please note, if an Aux cable is connected to the
speaker it will not play music from Bluetooth©
connected devices.
Audio Use
Follow the above connection steps to pair a
Bluetooth© device with the Speaker Trio. At this
point you can send any kind of audio signal to your
speaker (music, video, gaming, etc.). Just use your
device as normal and the audio will play through
your Speaker Trio.
Controls
Pressing the + and - buttons will increase or
decrease the volume on the Speaker Trio. Please
note that this will not effect the volume levels on
the connected device.
Connection
Laptop / notebook / PC
As the Bluetooth© versions for these types of
devices varies greatly, the connection methods will
differ as well. If you can not connect with the
Speaker Trio using the previous method instructed
you may need to install a new version of the
Bluetooth© driver. Please reference the
instructions of device for details.
Speaker Placement
The 3 individual speakers can be removed from the
Speaker Trio base to be set anywhere you like.
Approximate range is 115ft away from the base.
The Speaker Trio uses 2.4gHz signal so you're free
to put the speakers where you like!
AUX out
The Speaker Trio can also be used as a "bridge" to
wirelessly connect your devices to other speakers
not enabled with Bluetooth©.
Plug one end of the supplied Aux cable to the
"AUX OUT" port in the back of unit and plug the
other end of the cable to an "AUX IN" or "Line In"
port on any other speaker system
Please note, volume + & volume - on the Speaker
Trio lose function on this occasion and only the
connected Bluetooth© device or the connected
speaker itself can control the volume.
Charging
Connect your Speaker Trio base to an outlet using
the included power adapter. Place the speakers
onto the charging area of the base. The red
backlight will slowly flash during charging and
goes out when it has reached a complete charge
(Approx. 3.5 hours).
Operation Details
(cont.)
Charging Indicator Light Modes
•
Red LED / Flashing Fast: Battery is low, charge the unit soon.
•
Red LED / Flashing Slow: Speaker Trio is charging
•
Red LED / Turned Off: Battery is fully charged
Note: if the unit has not been used in the past 7 days please charge for 10 minutes before using the Speaker Trio.

Troubleshooting

Issue: Pairing is unsuccessfully after multiple attempts
Solution:
•
Check if the Bluetooth© indicator light is on. If the indicator light is off, please press the power button
to turn the unit on. If the Bluetooth© indicator light still doesn't come on after pressing the power
button, please charge the unit.
•
Check for other Bluetooth© devices around the surroundings that may interfere with searching and
turn devices off.
•
Power off and then power on the unit to restart the Bluetooth© function of the unit or your Bluetooth device
•
Unplug any cables plugged into the AUX IN, restart all devices and then attempt pairing again.
Issue: Interference or static during playback
Solution:
•
Avoid using the device between concrete or other building structures that may interfere with the signal.
•
Please check if the battery level of the unit and the Bluetooth© device and charge if necessary.
For more troubleshooting help go to http://bemwireless.com
Storage
•
Power off the Outlet Speaker If the unit will not be used for an extended period of time.
•
Do not set the unit in a damp environment, high temperatures or in direct sunlight.

Maintenance

•
Power off the unit
•
Use a soft, dry, lint-free cloth and wipe gently
•
Do not use alcohol, benzene, thinners or other chemical detergents as these can cause the casing to
be warped or discolored