Technical Specifications; Disposal Of Materials - Gymform ABS-A-Round PRO SPORT Bedienungsanleitung

ched the electrodes or if the contractions become weak du-
ring the session, it is likely that the batteries need to be re-
placed. Remove them and insert new ones. If this does not
solve the problem, the electrodes have probably reached
the end of their useful life. Switch off the GYMFORM®
ABS-A-ROUND PRO, take it off, fit new electrodes to the
belt and then resume your session. For your convenience,
GYMFORM® ABS-A-ROUND PRO will automatically set
the intensity level to 0 if you change the programme.
NOTE: If the unit does not work properly, press the RESET
button (located on the back of the unit) to restart the unit
and resume normal operation. Press the RESET button
(16) with the tip of a pen or pencil.

TECHNICAL SPECIFICATIONS:

10°C – 40°C Temperature
30%-75% RH (without condensation)
800-1600 hPa
Continuously operating device.
Ingress protection rating: IPX0
Power Supply: 3 1.5 V AAA batteries (not included)
Voltage: 3 x 1.5 V (4.5 V total)
A Impulse Frequency
Programme (Hz): min.-
width (µS)
max.
min.-max.
1
2
100
3
4 90/120
5
120
6
(Mean values at 1 kΩ)
Power: 3 W
Number of channels: 3 channels
The load impedance range for this product is from 500 Ω
-6-
to 20 kΩ.
Maximum current of the electrodes supplied: 120 mA (at
500 Ohm).
Dimensions: 92 x 82 x 33 mm (main unit).
Weight: 76 g (main unit without batteries).
This symbol indicates that the device is protected
against electrostatic discharge by BF-type double
insulation.
ISO 7000-1641 User Guide
CLEANING AND MAINTENANCE
DO NOT WASH THE GYMFORM® ABS-A-ROUND PRO
OR THE BELT: WIPE WITH A DRY OR DAMP CLOTH.
Remove the batteries from your GYMFORM® ABS-A-
ROUND PRO if you do not plan to use it for an extended
period of time.
CLEANING AND MAINTENANCE OF ADHESIVE
ELECTRODES
- Clean by wiping with wet fingers.
- Do not immerse in water.
- Keep in a cool, dry place at room temperature.
- Do not remove the insulating label.
Voltage
- After using the device, always replace the protective plas-
(V):
tic backings on the adhesive electrodes.
- Store in the bag supplied.
2
PRECAUTIONS WITH BATTERIES
90 Ensure the batteries are properly installed before turning
the unit on.
120
Turn off the unit to change the batteries.
50
Remove the batteries if you are not going to use the device
for an extended period of time.
10
Take the necessary precautions when disposing of the
batteries. Do not expose them to fire.
50

DISPOSAL OF MATERIALS

A symbol of a crossed-out wheeled bin means
you should find out about and follow local regula-
tions about disposing of this kind of product.
Do not dispose of this product as you would other
household waste. Dispose of this device in accor-
dance with the corresponding local regulations.
Electrical and electronic devices contain hazardous subs-
tances that can have harmful effects on the environment
and/or human health and should be recycled properly.
The battery should be disposed of separately. To protect
the environment, all batteries, including rechargeable
ones, should not be disposed of as you would other hou-
sehold waste. Take them to a disposal centre and ensure
it complies with applicable legislation on battery disposal.
Quality Warranty:
This product is covered by a warranty against manufactu-
ring defects subject to the time periods stipulated by the
legislation in force in each country.
This warranty does not cover damages resulting from in-
adequate use, negligent commercial use, abnormal wear
and tear, accidents or improper handling.
Australia & New Zealand only
This product has the benefit of certain Consumer Guaran-
tees. These are prescribed by the Australian Consumer
Law & the New Zealand Consumer Guarantees Act 1993
both of which provide protection for consumers. There is
no express warranty for this product in Australia or New
Zealand. The above paragraph refers to other countries.
Made in China.