Inhaltsverzeichnis
Werbung
DESCRIPTION
(starts at page 85)
A
1
Seat
2
Steering wheel
3
Grass catcher bag
4
Blade
5
Ignition key
TECHNICAL DETAILS
Engine
Electric starter
Advance
Maximum speed
Grass collection bin
Body
Cutting plate
Cutting width
Cutting height regulation
Curvature radius
Grass collection bag
Tyres
Weight with collection bag
B
ASSEMBLY OF THE GRASS COLLECTION SACK
The grass collection bag is included with all ride-on lawnmowers as a standard
If the bag comes with the product then it not an accessory therefore delete the
word accessory and replace with part.
For assembly, you need the following parts:
- 1 Frame
- 2 Hexagonal screws (M6x16)
- 3 self-locking nuts (M5)
ASSEMBLY
UNPACKING/ ASSEMBLY
The ride-on lawnmower is packed in a carton and is ready assembled apart from the
steering wheel, seat, grass collection bag and front wheels. Please observe the follow-
ing sequence when unpacking the machine:
1. Unpack all the parts that have been delivered. Dispose of the carton and pallet in an
environmentally friendly way.
2. Check all the parts
3. Begin assembly.
WHEEL ASSEMBLY (starts at page 85)
C
1. Mount the front wheels on the pins (15), positioning a washer (16), the wheel
(17) and a washer (18).
2. Secure with a stop (19).
3. Mount the rear wheels on the pins.
STEERING WHEEL ASSEMBLY (starts at page 86)
D
1. Fix the steering wheel (2) pushing until it is connected with the steering column
(20).
2. Secure the steering wheel (2) by means of the socket pin (21); put the
socket pin through the openings (on the steering column and steering wheel)
ENGINE GUARD ASSEMBLY (see page 86)
D
1
Insert the two rear ends into the special slots in the casing and fix the guard by
inserting the washers and M5 nuts on M5 x 20 screws and fix to the casing.
SEAT ASSEMBLY (starts at page 86)
D
2
1. Fasten the seat (1) to the support plate (22) through the 4 M8 x 18 screws.
Assemble with 4 washers Ø 9 x 24 and 4 grower.
2. Before tightening the screws, adjust the position of the seat on the holes of
the plate to suit the user's needs.
ASSEMBLY OF THE GRASS COLLECTION BAG (starts at page 86)
D
3
Fasten the bin to the rear part of the ride-on-mower with the 2 H.H. 6x16, 2 screws, the 2 Z-
shaped plates and 2 M5 nuts.
ADJUSTING THE CUTTING HEIGHT
Before the cutting height is adjusted, the engine must be switched off and
the blades must have come to complete standstill.
E
ADJUSTMENT (starts at page 86)
1. Push the adjustment lever (12) outwards in order to release it from its seat.
2. Push the lever into the required notch for the cutting height.
3. Release the lever slowly till it sticks in the notch.
The cutting height is now set.
6
Throttle lever
7
Battery
8
Blade coupling lever
9
Brake pedal
10 Brake lever
Height
front
265 mm
rear
360 mm
8,5 Hp ÷ 12,5 Hp
Electric
Five forward gears and one reverse gear.
9,0 Km/h
2000 mm x 820 mm x 1020 mm
Polypropylene
Sheet steel
67 - 76 cm
Centralised on 5 positions
1,5 m
150 litre
Width
85 mm
120 mm
145
(starts at page 85)
- 1 Fabric bag with clips
- 2 Z-shaped plates
1. Allow the bag to slide on the frame and secure with suitable clips.
It is strictly forbidden to start the ride-on lawnmower (even for trial purposes)
without completing assembly.
Attention: Assemble the wheel with valve outwards.
The openings at the steering wheel and at the steering column must be in
exact alignment.
Check at regular intervals that the nuts are tightly screwed down.
15
11 Gear lever (MEC)
12 Agjusting levers for cutting height
13 Motor safety housing
14 Pilot light for check-in and for full grass collection bin
15 Advance pedal (HYDRO)
Recommended pressure
1,5 bar
2 bar
ENGLAND
Werbung
Inhaltsverzeichnis
